Tolerance x.xx = !0.01 (!0.25)

Pin 1 is marked by a “dot” or indentation on the side of the unit

Model

Number

Input

Output

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

G101R

5

4.5 - 5.5

213

28

3.3

200.0

20.0

62

500

G102R

5

4.5 - 5.5

317

28

5.0

200.0

20.0

63

500

G103R

5

4.5 - 5.5

312

26

9.0

111.0

11.0

64

500

G104R

5

4.5 - 5.5

312

26

12.0

83.0

9.0

64

500

G105R

5

4.5 - 5.5

312

38

15.0

66.0

7.0

66

500

G111R

12

10.8 - 13.2

91

16

3.3

200.0

20.0

61

200

G112R

12

10.8 - 13.2

130

16

5.0

200.0

20.0

64

200

G113R

12

10.8 - 13.2

130

16

9.0

111.0

11.0

64

200

G114R

12

10.8 - 13.2

130

16

12.0

83.0

9.0

64

200

G115R

12

10.8 - 13.2

130

16

15.0

66.0

7.0

64

200

G121R

24

21.6 - 26.4

43

7

3.3

200.0

20.0

63

100

G122R

24

21.6 - 26.4

64

7

5.0

200.0

20.0

65

100

G123R

24

21.6 - 26.4

65

9

9.0

111.0

11.0

64

100

G124R

24

21.6 - 26.4

65

9

12.0

83.0

9.0

64

100

G125R

24

21.6 - 26.4

65

9

15.0

66.0

7.0

64

100

232 Tosca Drive, Stoughton, MA 02072

www.micropowerdirect.com

sales@micropowerdirect.com

phone: (781) 344 - 8226 * fax: (781) 344 - 8481

Mechanical Dimensions

MicroPower

Direct

Pin

Single

1-Vin

7NC

9+Vout

11

-Vout

14

+Vin

NC = No Connection

Pin Connections

µF Max

33

Capacitive Load

Model Selection Guide

Derating Curve

Ambient Temperature 1C

85

-40

-20

0

5

15

25

35

45

55

65

75

95

105

0

20

40

60

80

100

0.80 (20.32)

11

9

1

14

0.10

(2.54)

0.60 (15.24)

0.10

(2.54)

0.01

(0.25)

0.01

(0.25)

0.40

(10.2)

0.12

(3.05)

0.05

(1.25)

Bottom

Side

7

0.27

(6.85)

Notes:

1. These units do not require

external comonents to oper-

ate, but the use of an input

capacitor (10 µF) may en-

hance performance in some

applications. An output cap-

acitor (4.7 µF to 10 µF) may

be used to reduce ripple.