Notes:

Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

G201EI

5

4.5 - 5.5

500

30

5.0

400.0

40.0

15

80

1,000

G202EI

5

4.5 - 5.5

494

30

9.0

222.0

23.0

15

81

1,000

G203EI

5

4.5 - 5.5

488

30

12.0

167.0

17.0

15

82

1,000

G204EI

5

4.5 - 5.5

476

30

15.0

133.0

14.0

15

84

1,000

G205EI

5

4.5 - 5.5

488

30

±5.0

±200.0

±20.0

15

82

1,000

G206EI

5

4.5 - 5.5

482

30

±9.0

±111.0

±12.0

15

83

1,000

G207EI

5

4.5 - 5.5

470

30

±12.0

±83.0

±9.0

15

85

1,000

G208EI

5

4.5 - 5.5

470

30

±15.0

±67.0

±7.0

15

85

1,000

G211EI

12

10.8 - 13.2

208

15

5.0

400.0

40.0

15

80

500

G212EI

12

10.8 - 13.2

201

15

9.0

222.0

23.0

15

83

500

G213EI

12

10.8 - 13.2

198

15

12.0

167.0

17.0

15

84

500

G214EI

12

10.8 - 13.2

196

15

15.0

133.0

14.0

15

85

500

G215EI

12

10.8 - 13.2

201

15

±5.0

±200.0

±20.0

15

83

500

G216EI

12

10.8 - 13.2

198

15

±9.0

±111.0

±12.0

15

84

500

G217EI

12

10.8 - 13.2

194

15

±12.0

±83.0

±9.0

15

86

500

G218EI

12

10.8 - 13.2

194

15

±15.0

±67.0

±7.0

15

86

500

G221EI

24

21.6 - 26.4

103

8

5.0

400.0

40.0

15

81

250

G222EI

24

21.6 - 26.4

99

8

9.0

222.0

23.0

15

84

250

G223EI

24

21.6 - 26.4

98

8

12.0

167.0

17.0

15

85

250

G224EI

24

21.6 - 26.4

97

8

15.0

133.0

14.0

15

86

250

G225EI

24

21.6 - 26.4

99

8

±5.0

±200.0

±20.0

15

84

250

G226EI

24

21.6 - 26.4

98

8

±9.0

±111.0

±12.0

15

85

250

G227EI

24

21.6 - 26.4

96

8

±12.0

±83.0

±9.0

15

87

250

G228EI

24

21.6 - 26.4

96

8

±15.0

±67.0

±7.0

15

87

250

Pin

Single

Dual

Pin

Single

Dual

1

-Vin

-Vin

9

No Pin

Common

7

NC

NC

10

-Vout

-Vout

8

+Vout

+Vout

14

+Vin

+Vin

Derating Curve

Notes:

1. Output load regulation is specified for a load change of 10% to

100%.

2. These units should not be operated with a load under 10% of

full load. Operation at no-load may cause damage to the unit.

3. These converters will operate without external components.

However, when measuring output ripple, it is recommended

that an external ceramic capacitor be placed from the +Vout

pin to the -Vout pin for single output units and from each out-

put to common for dual output units. An input capacitor will

enhance stability over temperature and input line variations.

Recommended capacitor values are given in the table below.

For applications requiring very low output noise levels, a simple

LC filter should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V

or 30 VDC output. To do this, connect the load across the posi-

tive (+Vout) and negative (-Vout) outputs and float the output

common

5. It is recommended that a fuse be used on the input of a power

supply for protection. See the Model Selection table above for

the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7 μF

5 VDC

10.0 μF

4.7 μF

12 VDC

2.2 μF

9 VDC

4.7 μF

2.2 μF

24 VDC

1.0 μF

12 VDC

2.2 μF

1.0 μF

15 VDC

1.0 μF

0.47 μF

Model Selection Guide

Mechanical Dimensions

Pin Connections

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com