Electronic Components Datasheet Search
  English  ▼

X  

TPS56302 Datasheet(PDF) 13 Page - Texas Instruments

Part # TPS56302
Description  DUAL-OUTPUT LOW-INPUT-VOLTAGE DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
PDF  34 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI [Texas Instruments]
Direct Link  http://www.ti.com
Logo TI - Texas Instruments

TPS56302 Datasheet(HTML) 13 Page - Texas Instruments

Back Button TPS56302 Datasheet HTML 9Page - Texas Instruments TPS56302 Datasheet HTML 10Page - Texas Instruments TPS56302 Datasheet HTML 11Page - Texas Instruments TPS56302 Datasheet HTML 12Page - Texas Instruments TPS56302 Datasheet HTML 13Page - Texas Instruments TPS56302 Datasheet HTML 14Page - Texas Instruments TPS56302 Datasheet HTML 15Page - Texas Instruments TPS56302 Datasheet HTML 16Page - Texas Instruments TPS56302 Datasheet HTML 17Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 34 page
background image
TPS56302
DUAL-OUTPUT LOW-INPUT-VOLTAGE
DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
SLVS289 – MARCH 2000
13
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
detailed description (continued)
deadtime control
Deadtime control prevents shoot-through current from flowing through the main power FETs during switching
transitions by actively controlling the turnon time of the MOSFET drivers. The high-side driver is not allowed
to turn on until the gate drive voltage to the low-side FET is below 1 V, and the low-side driver is not allowed
to turn on until the voltage at the junction of the 2 FETs (Vphase) is below 2 V.
current sensing
Current sensing is achieved by sampling and holding the voltage across the high-side power FET while the
high-side FET is on. The sampling network consists of an internal 60-
Ω switch and an external hold capacitor.
Internal logic controls the turnon and turnoff of the sample/hold switch such that the switch does not turn on until
the Vphase voltage transitions high, and the switch turns off when the input to the high-side driver goes low.
Thus sampling will occur only when the high-side FET is conducting current. The voltage on the IOUT pin equals
2 times the sensed high-side voltage.
droop compensation
The droop compensation network reduces the load transient overshoot / undershoot on VOUT, relative to VREF
(see the
application information section of this document for more details). VOUT is programmed to a voltage
greater than VREF by an external resistor divider from VOUT to the VSENSE pin to reduce the undershoot on
VOUT during a low to high load transient. The overshoot during a high to low load transient is reduced by
subtracting the voltage that is on the DROOP pin from VREF. The voltage on the IOUT pin is divided down with
an external resistor divider, and connected to the DROOP pin.
inhibit
INHIBIT is a TTL-compatible comparator pin that is used to enable the controller. When INHIBIT is lower than
the threshold, the output drivers are low and the slow-start capacitor is discharged. When INHIBIT goes high
(above 2.1 V), the short across the slow-start capacitor is released and normal converter operation begins.
When another system logic supply is connected to the INHIBIT pin, this pin controls power sequencing by
locking out controller operation until the system logic supply exceeds the input threshold voltage of the inhibit
circuit; thus the +3.3-V supply and another system logic supply (either +5 V or +12 V) must be above UVLO
thresholds before the controller is allowed to start up. Toggling the INHIBIT pin from low to high or recycling VCC
clears the fault latch.
slow-start
The slow-start circuit controls the rate at which both VOUT–RR and VOUT–LDO power up (at the same time). A
capacitor is connected between the SLOWST and ANAGND pins and is charged by an internal current source.
The value of the current source is proportional to the reference voltage, so that the charging rate of CSLOWST
is proportional to the ripple regulator reference voltage. The slow-start charging current is determined by the
following equation:
I
SLOWSTART +
I
VREFB
5
Where IVREFB is the current flowing out of the VREFB pin. It is recommended that no additional loads be
connected to VREFB, other than the resistor divider for setting the hysteresis voltage. Thus these resistor values
will determine the slow-start charging current. The maximum current that can be sourced by the VREFB circuit
is 500
µA. The equation for the slow-start time is:
T
SLOWSTART +
5
C
SLOWSTART
R
VREFB
Where RVREFB is the total external resistance from VREFB to ANAGND.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com