X25F016PI datasheet(8/16 Pages) XICOR

8 / 16 page

X25F064/032/016/008

*COMMENT

Stresses above those listed under “Absolute Maximum

Ratings” may cause permanent damage to the device.

This is a stress rating only and the functional operation

of the device at these or any other conditions above

those listed in the operational sections of this specification

is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect device reliability.

ABSOLUTE MAXIMUM RATINGS*

Temperature Under Bias .................. –65

°C to +135°C

Storage Temperature ....................... –65

°C to +150°C

Voltage on any Pin with Respect to VSS ......... –1V to +7V

D.C. Output Current ............................................. 5mA

Lead Temperature

(Soldering, 10 Seconds) ............................. 300

°C

D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)

Limits

Symbol

Parameter

Min.

Max.

Units

Test Conditions

ICC

VCC Supply Current (Active)

SCK = VCC x 0.1/VCC x 0.9 @ 1MHz,

SO = Open,

CS = VSS

ISB1(2) VCC Supply Current (Standby)

µA

CS = VCC, VIN = VSS or VCC, VCC = 3.6V

ISB2

VCC Supply Current (Standby)

µA

CS = VCC, VIN = VSS or VCC, VCC = 5V

ILI

Input Leakage Current

µAVIN = VSS to VCC

ILO

Output Leakage Current

–1

µAVOUT = VSS to VCC

VIL(1)

Input LOW Voltage

VCC x 0.7 VCC x 0.3

VIH(1)

Input HIGH Voltage

VCC + 0.5

VOL1

Output LOW Voltage

0.4

IOL = 1.5mA, VCC = 2.7V

VOH1

Output HIGH Voltage

VCC – 0.3

IOH = –0.4mA, VCC = 2.7V

VOL2

Output LOW Voltage

0.4

IOL = 3mA, VCC = 5V

VOH2

Output HIGH Voltage

VCC – 0.8

IOH = –1.6mA, VCC = 5V

6685 PGM T08.4

RECOMMENDED OPERATING CONDITIONS

Temp

Min.

Max.

Commercial

°C

+70

°C

Extended

–20

°C

+85

°C

Industrial

–40

°C

+85

°C

6685 PGM T06.2

Supply Voltage

Limits

X25F064/032/016/008

1.8V to 3.6V

X25F064/032/016/008–5

4.5V to 5.5V

6685 PGM T07.3

POWER-UP TIMING

Symbol

Parameter

Min.

Max.

Units

tPUR(3)

Power-up to Read Operation

tPUW(3)

Power-up to Write Operation

6685 PGM T09

Notes:

(1) VIL min. and VIH max. are for reference only and are not tested.

(2) This parameter is periodically sampled and not 100% tested.

(3) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. These parameters

are periodically sampled and not 100% tested.

CAPACITANCE TA = 25°C, f = 1MHz, VCC = 5V.

Symbol

Test

Max.

Units

Conditions

COUT(2)

Output Capacitance (SO)

VOUT = 0V

CIN(2)

Input Capacitance (SCK, SI,

CS, WP, HOLD)6

VIN = 0V

6685 PGM T10.1

X25F016PI Datasheet(PDF) 8 Page - Xicor Inc.

X25F016PI Datasheet(HTML) 8 Page - Xicor Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Download

Link URL