2

INPUT SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Input Voltage - AC

Continuous input range.

MAP42

85

264

VAC

MAP30, MAP40

90

264

Input Frequency

AC input.

47

63

Hz

Brown Out Protection

Lowest AC input voltage that regulation is maintained with full rated loads.

85

VAC

Hold-up Time

Nominal AC Input Voltage (115VAC), full rated load.

15

mS

Input Current

90 VAC (40W load).

1.2

Input Protection

Non-user serviceable internally located AC input line fuse.

Inrush Surge Current

Internally limited by thermistor. Vin = 264VAC (one cycle). 25° C.

38

Operating Frequency

Switching frequency of power supply (fixed frequency).

23

25

30

kHz

OUTPUT SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Efficiency

Full load, 120VAC.

70

%

Minimum Loads

Single output models; MAP30, MAP42.

0.0

Amps

All multiple output models, see regulation graphs.

Ripple and Noise

Full load, 20MHz bandwidth.

See Model Selection Chart.

Output Power

Multiple output models with convection cooling.

40

Watts

Overshoot / Undershoot

Output voltage overshoot/undershoot at turn-on, V1.

1

%

Regulation

Varies by output, total regulation includes: Line changes from 90-132

VAC or 175-264, changes in load starting at 20% load and changing

See regulation graphs.

to 100% load.

Transient Response

Recovery time, to within 1% of initial set point due to a 50-100%

500

µS

load change, 4% max. deviation. (Main output only of multiple output units).

Turn-on Delay

Time required for initial output voltage stabilization.

1

2

Sec

Turn-on Rise Time

Time required for output voltage to rise from 10% to 90%.

20

mS

INTERFACE SIGNALS AND INTERNAL PROTECTION

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

MAP30-1005, MAP42-1005

5.8

6.8

Overvoltage

MAP42-1012

20.0

22.0

V

Protection

MAP42-1024

32.0

37.0

Main output only of multiple output units.

5.8

6.8

Overload

Fully protected against output overload and short circuit. Automatic

130

%

Protection

recovery upon removal of overload condition.

Remote Sense

Total cable drop, single output models only.

250

mV

SAFETY, REGULATORY, AND EMI SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Agency Approvals

UL1950.

CSA 22.2 No. 234/950.

Approved.

EN60950 (TUV).

Dielectric Withstand

Input to output.

2600

VDC

Voltage

Electromagnetic

FCC CFR title 47 part 15 sub-part B - conducted.

B

Interference

EN55022 / CISPR 22 conducted (Note 1).

B

Class

EN55022 / CISPR 22 radiated (Note 2).

B

Input Transient

EN61000-4-5 Level 3

Line to Line

1

kV

Protection

Line to Ground

2

Insulation Resistance

Input to output.

7

M

Ω

Leakage Current

Per EN60950, 264VAC

MAP42, MAP40-3100, 3001, 3105, 3500

500

µA

MAP30-1005, MAP40-3000, MAP40-3003

750

NOTES: 1) MAP30-1005, MAP40-3000, MAP40-3003 meet Class A.

2) MAP40-3000, MAP40-3003, MAP3500 meet Class A.

MAP30/40/42 SERIES