2

MAP80 SERIES

MODEL

OUTPUT

ADJUSTMENT

OUTPUT

PEAK OUTPUT

LINE

LOAD

RIPPLE & NOISE

INITIAL SETTING

VOLTAGE

RANGE

CURRENT

CURRENT (NOTE 1)

REGULATION

REGULATION

%p-p (NOTE 2)

ACCURACY

+5V

4.8V to 5.5V

14A

16A

0.2%

1%

1%

5.1V to 5.2V

MAP80-4010

+12V

11.52V to 12.48V

4A

7A

0.2%

1%

1%

12.0V to 12.1V

-5V

Fixed

1A

1A

0.5%

2%

1%

-4.8V to -5.4V

-12V

Fixed

3A

3A

0.5%

2%

1%

-11.5V to -12.5V

+5V

4.8V to 5.5V

14A

16A

0.2%

1%

1%

5.1V to 5.2V

MAP80-4020

+12V

11.52V to 12.48V

4A

7A

0.2%

1%

1%

12.0V to 12.1V

-12V

Fixed

1A

1A

0.5%

2%

1%

-11.5V to -12.5V

-5V

Fixed

3A

3A

0.5%

2%

1%

-4.8V to -5.4V

NOTES:

1) Peak loads up to 90 Watts for 60 seconds or less are acceptable, (10% duty cycle max.). Peak power must not exceed 90 Watts.

2) Maximum peak to peak noise expressed as a percentage of output voltage, 20MHz bandwidth.

INPUT SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Input Voltage - AC

Continuous input range.

90

135

VAC

175

264

Input Frequency

AC input.

47

63

Hz

Brown Out Protection

Lowest AC input voltage that regulation is maintained with full rated loads.

90

VAC

Hold-up Time

Nominal AC input voltage (115VAC), full rated load.

20

mS

Input Current

90 VAC (80W load).

2.5

110VAC (80W load).

2.8

Input Protection

Non-user serviceable internally located AC input line fuse.

Inrush Surge Current

Internally limited by thermistor. Vin = 264VAC (one cycle). 25° C.

45

Operating Frequency

Switching frequency of power supply (varies with load).

22

120

kHz

OUTPUT SPECIFICATIONS

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Efficiency

Full load, 115VAC. Varies with distribution of loads among outputs.

73

75

80

%

Minimum Loads

MAP80-1012

0.42

MAP80-1024

0.21

Amps

MAP80-1005 and all multiple output models, main channel only.

1.00

Ripple and Noise

Full load, 20MHz bandwidth.

See Model Selection Chart.

Output Power

Continuous output power, all multiple output models.

80

Watts

Peak output power (60s maximum, 10% duty cycle), all multiple output models.

90

Watts

Overshoot / Undershoot

Output voltage overshoot/undershoot at turn-on, V1, V2.

1

%

Regulation

Varies by output. Total regulation includes: line changes from 90-132 VAC

See Model Selection Chart.

or 175-264, changes in load starting at 20% load and changing to 100% load.

Transient Response

Recovery time, to within 1% of initial set point due to a 50-100%

500

µS

load change, 4% max. deviation. (Main output of multiple output units).

Turn-On Delay

Time required for initial output voltage stabilization.

1

5

Sec

Turn-on Rise Time

Time required for output voltage to rise from 10% to 90%.

20

mS

INTERFACE SIGNALS AND INTERNAL PROTECTION

PARAMETER

CONDITIONS/DESCRIPTION

MIN

NOM

MAX

UNITS

Overvoltage

Provided on MAP80-1005 and the main output of multiple output units.

5.5

6.8

Protection

MAP80-1012

17

23

V

MAP80-1024

32

37

Overload Protection

Fully protected against output overload and short circuit. Automatic recovery upon removal of overload condition.

Power Fail

TTL compatible logic signal. Time before regulation dropout

Warning (Note 1)

due to loss of input power at 110VAC.

4

mS

NOTES:

1) Power Fail Warning is not available on MAP80-1024. The MAP80-1012 is an open collector output, capable of sinking 35 mA, maximum.

NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments,

or nuclear control systems without the express written consent of the President of Power-One, Inc.

TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are

subject to change without notice.