MSP430F412IPM datasheet(22/64 Pages) TI

22 / 64 page

MSP430x41x

MIXED SIGNAL MICROCONTROLLER

SLAS340J − MAY 2001 − REVISED DECEMBER 2008

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

electrical characteristics over recommended operating free-air temperature (unless otherwise

noted)

supply current into AVCC + DVCC excluding external current (see Note 1)

PARAMETER

TEST CONDITIONS

VCC

MIN

TYP

MAX

UNIT

Active mode,

C41x

2.2 V

160

200

Active mode,

f(MCLK) = f(SMCLK) = f(DCO) = 1 MHz,

C41x

°Cto85°C

3 V

240

300

I(AM)

f(MCLK) = f(SMCLK) = f(DCO) = 1 MHz,

f(ACLK) = 32,768 Hz, XTS_FLL = 0

F41x

TA = −40°C to 85°C

2.2 V

200

250

μA

(ACLK)

(F41x: Program executes in flash)

F41x

3 V

300

350

Low-power mode (LPM0)

f(MCLK) = f(SMCLK) = f(DCO) = 0.5 MHz,

2.2 V

f(MCLK) = f(SMCLK) = f(DCO) = 0.5 MHz,

f(ACLK) = 32,768 Hz, XTS_FLL = 0

FN_8=FN_4=FN_3=FN_2=0 (see Note 3)

C41x

°Cto85°C

3 V

I(LPM0)

Low-power mode (LPM0)

f(MCLK) = f(SMCLK) = f(DCO) = 1 MHz,

C41x

F41x

TA = −40°C to 85°C

2.2 V

μA

f(MCLK) = f(SMCLK) = f(DCO) = 1 MHz,

f(ACLK) = 32,768 Hz, XTS_FLL = 0

FN_8=FN_4=FN_3=FN_2=0 (see Note 3)

3 V

100

Low power mode (LPM2) (see Note 3)

°Cto85°C

2.2 V

I(LPM2)

Low-power mode (LPM2) (see Note 3)

TA = −40°C to 85°C

3 V

μA

TA = −40°C

0.95

1.4

TA = −10°C

0.8

1.3

TA = 25°C

2.2 V

0.7

1.2

TA = 60°C

2.2 V

0.95

1.4

Low power mode (LPM3) (see Note 2 and Note 3)

TA = 85°C

1.6

2.3

I(LPM3)

Low-power mode (LPM3) (see Note 2 and Note 3)

TA = −40°C

1.1

1.7

μA

TA = −10°C

1.0

1.6

TA = 25°C

3 V

0.9

1.5

TA = 60°C

3 V

1.1

1.7

TA = 85°C

2.0

2.6

TA = −40°C

0.1

0.5

I(LPM4)

Low-power mode (LPM4) (see Note 3)

TA = 25°C

2.2 V/3 V

0.1

0.5

μA

I(LPM4)

Low power mode (LPM4) (see Note 3)

TA = 85°C

2.2 V/3 V

0.8

2.5

μA

NOTES:

1. All inputs are tied to 0 V or VCC. Outputs do not source or sink any current. The current consumption is measured with active Basic

Timer1 and LCD (ACLK selected).

The current consumption of the Comparator_A and the SVS module are specified in the respective sections.

2. The LPM3 currents are characterized with a KDS Daishinku DT−38 (6 pF) crystal.

3. Current for brownout included.

current consumption of active mode versus system frequency

I(AM) = I(AM) [1 MHz] × f(System) [MHz]

current consumption of active mode versus supply voltage

I(AM) = I(AM) [3 V] + 140 μA/V × (VCC – 3 V)

MSP430F412IPM Datasheet(PDF) 22 Page - Texas Instruments

MSP430F412IPM Datasheet(HTML) 22 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Datasheet Download

Link URL