HT48R005 datasheet(22/62 Pages) HOLTEK

22 / 62 page

HT48R005/HT46R005

Rev. 1.00

November 29, 2011

increased current consumption. Care must also be

taken with the loads, which are connected to I/O pins,

which are setup as outputs. These should be placed in a

condition in which minimum current is drawn or con-

nected only to external circuits that do not draw current,

such as other CMOS inputs.

If the configuration options have enabled the Watchdog

Timer internal oscillator LIRC then this will continue to

run when in the Sleep Mode and will thus consume

some power. For power sensitive applications it may be

therefore preferable to use the system clock source for

the Watchdog Timer.

Wake-up

After the system enters the Sleep Mode, it can be woken

up from one of various sources listed as follows:

· An external reset

· An external falling edge on PA0 to PA7

· A system interrupt

· A WDT overflow

If the system is woken up by an external reset, the de-

vice will experience a full system reset, however, if the

device is woken up by a WDT overflow, a Watchdog

Timer reset will be initiated. Although both of these

wake-up methods will initiate a reset operation, the ac-

tual source of the wake-up can be determined by exam-

ining the TO and PDF flags. The PDF flag is cleared by a

system power-up or executing the clear Watchdog

Timer instructions and is set when executing the

²HALT²

instruction. The TO flag is set if a WDT time-out occurs,

and causes a wake-up that only resets the Program

Counter and Stack Pointer, the other flags remain in

their original status.

Pins PA0 to PA7 can be setup via the PAWK register to

permit a negative transition on the pin to wake-up the

system. When a PA0 to PA7 pin wake-up occurs, the pro-

gram will resume execution at the instruction following

the

²HALT² instruction.

If the system is woken up by an interrupt, then two possi-

ble situations may occur. The first is where the related

interrupt is disabled or the interrupt is enabled but the

stack is full, in which case the program will resume exe-

cution at the instruction following the

²HALT² instruction.

In this situation, the interrupt which woke-up the device

will not be immediately serviced, but will rather be ser-

viced later when the related interrupt is finally enabled or

when a stack level becomes free. The other situation is

where the related interrupt is enabled and the stack is

not full, in which case the regular interrupt response

takes place. If an interrupt request flag is set to

²1² be-

fore entering the Sleep Mode, then any future interrupt

requests will not generate a wake-up function of the re-

lated interrupt will be ignored.

No matter what the source of the wake-up event is, once

a wake-up event occurs, there will be a time delay be-

fore normal program execution resumes. Consult the ta-

ble for the related time.

Wake-up Source

Oscillator Type

ERC, IRC

HXT

External RES, Power-on

Reset and LVR

tRSTD +

tSST1

tRSTD +

tSST2

PA Port

tSST1

tSST2

Interrupt

WDT Overflow

Note:

1. tRSTD (reset delay time), tSYS (system clock)

2. tRSTD is power-on delay, typical time=100ms

3. tSST1=2

´ tSYS

4. tSST2= 128

´ tSYS

Wake-up Delay Time

HT48R005 Datasheet(PDF) 22 Page - Holtek Semiconductor Inc

HT48R005 Datasheet(HTML) 22 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62

Datasheet Download

Link URL