AFS090 datasheet(154/334 Pages) MICROSEMI

154 / 334 page

Device Architecture

2- 13 8

R e v isio n 2

Features Supported on Pro I/Os

Table 2-72 lists all features supported by transmitter/receiver for single-ended and differential I/Os.

Table 2-72 • Fusion Pro I/O Features

Feature

Description

Single-ended

and

voltage-

referenced transmitter

features

•

Hot insertion in every mode except PCI or 5 V input tolerant (these modes use

clamp diodes and do not allow hot insertion)

•

Activation of hot insertion (disabling the clamp diode) is selectable by I/Os.

•

Weak pull-up and pull-down

•

Two slew rates

•

Skew between output buffer enable/disable time: 2 ns delay (rising edge) and

0 ns delay (falling edge); see "Selectable Skew between Output Buffer

Enable/Disable Time" on page 2-151 for more information

•

Five drive strengths

•

5 V–tolerant receiver ("5 V Input Tolerance" section on page 2-146)

•

LVTTL/LVCMOS 3.3 V outputs compatible with 5 V TTL inputs ("5 V Output

Tolerance" section on page 2-150)

•

High performance (Table 2-76 on page 2-145)

Single-ended receiver features

•

Schmitt trigger option

•

ESD protection

•

Programmable delay: 0 ns if bypassed, 0.625 ns with '000' setting, 6.575 ns

with '111' setting, 0.85-ns intermediate delay increments (at 25°C, 1.5 V)

•

High performance (Table 2-76 on page 2-145)

•

Separate ground planes, GND/GNDQ, for input buffers only to avoid output-

induced noise in the input circuitry

Voltage-referenced

differential

receiver features

•

Programmable Delay: 0 ns if bypassed, 0.625 ns with '000' setting, 6.575 ns

with '111' setting, 0.85-ns intermediate delay increments (at 25°C, 1.5 V)

•

High performance (Table 2-76 on page 2-145)

•

Separate ground planes, GND/GNDQ, for input buffers only to avoid output-

induced noise in the input circuitry

CMOS-style

LVDS,

BLVDS,

M-LVDS, or LVPECL

transmitter

•

Two I/Os and external resistors are used to provide a CMOS-style LVDS,

BLVDS, M-LVDS, or LVPECL transmitter solution.

•

Activation of hot insertion (disabling the clamp diode) is selectable by I/Os.

•

Weak pull-up and pull-down

•

Fast slew rate

LVDS/LVPECL differential

receiver features

•

ESD protection

•

High performance (Table 2-76 on page 2-145)

•

Programmable delay: 0.625 ns with '000' setting, 6.575 ns with '111' setting,

0.85-ns intermediate delay increments (at 25°C, 1.5 V)

•

Separate input buffer ground and power planes to avoid output-induced noise

in the input circuitry

AFS090 Datasheet(PDF) 154 Page - Microsemi Corporation

AFS090 Datasheet(HTML) 154 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL