Electronic Components Datasheet Search
  English  ▼

X  

ADV3205 Datasheet(PDF) 16 Page - Analog Devices

Part # ADV3205
Description  60 MHz, G = 2, 16 횞 16
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

ADV3205 Datasheet(HTML) 16 Page - Analog Devices

Back Button ADV3205 Datasheet HTML 12Page - Analog Devices ADV3205 Datasheet HTML 13Page - Analog Devices ADV3205 Datasheet HTML 14Page - Analog Devices ADV3205 Datasheet HTML 15Page - Analog Devices ADV3205 Datasheet HTML 16Page - Analog Devices ADV3205 Datasheet HTML 17Page - Analog Devices ADV3205 Datasheet HTML 18Page - Analog Devices ADV3205 Datasheet HTML 19Page - Analog Devices ADV3205 Datasheet HTML 20Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 16 / 20 page
background image
ADV3205
Data Sheet
Rev. 0 | Page 16 of 20
POWER-ON RESET
When powering up the ADV3205, it is usually desirable to have
the outputs start up in the disabled state. The RESET pin, when
taken low, causes all outputs to be in the disabled state. However,
the RESET signal does not reset all registers in the
.
This is important when operating in parallel programming mode.
Refer to the
section for information
about programming internal registers after power-up. Serial
programming programs the entire matrix each time; therefore,
no special considerations apply.
ADV3205
Parallel Programming
Because the data in the shift register is random after power-up,
do not use it to program the matrix or the matrix can enter
unknown states. To prevent this, do not apply logic low signals
to both CE and UPDATE initially after power-up. First, load the
shift register with the desired data, and then take UPDATE low
to program the device.
The RESET pin has a 20 kΩ pull-up resistor to DVCC that can be
used to create a simple power-up reset circuit. A capacitor from
RESET to ground holds RESET low for some time while the rest
of the device stabilizes. The low condition causes all outputs to
be disabled. The capacitor then charges through the pull-up resistor
to the high state, thus allowing full programming capability of
the device.
MANAGING VIDEO SIGNALS
Video signals often use controlled impedance transmission lines
that are terminated in their characteristic impedance. Although this
is not always the case, there are some considerations when using
the ADV3205 to route video signals with controlled impedance
transmission lines. Figure 29 shows a schematic of an input
and output treatment of a typical video channel.
75Ω
75Ω
75Ω
75Ω
TRANSMISSION
LINE
TYPICAL
OUTPUT
+5V
ADV3205
G = 2
–5V
TYPICAL
INPUT
75Ω
VIDEO
SOURCE
Figure 29. Video Signal Circuit
Video signals most often use 75 Ω transmission lines that need
to be terminated with this value of resistance at each end. When
such a source is delivered to one of the ADV3205 inputs, the
high input impedance does not properly terminate these signals.
Therefore, terminate the line with a 75 Ω shunt resistor to
ground. Because video signals are limited in their peak-to-peak
amplitude (typically no more than 1.5 V p-p), there is no need
to attenuate video signals before they pass through the ADV3205.
The ADV3205 outputs are low impedance and do not properly
terminate the source end of a 75 Ω transmission line. In these
cases, insert a series 75 Ω resistor at an output that drives a video
signal. Then terminate the 75 Ω transmission line with 75 Ω at
its far end. This overall termination scheme divides the amplitude
of the ADV3205 output by two. An overall unity-gain channel is
produced because of the channel gain-of-two of the ADV3205.
CREATING LARGER CROSSPOINT ARRAYS
The ADV3205 is a high density building block for creating
crosspoint arrays of dimensions larger than 16 × 16. Various
features, such as output disable and chip enable, are useful for
creating larger arrays.
The first consideration in constructing a larger crosspoint is to
determine the minimum number of devices that are required. The
16 × 16 architecture of the ADV3205 contains 256 points, which is
a factor of 64 greater than a 4 × 1 crosspoint (or multiplexer). The
printed circuit board (PCB) area, power consumption, and design
effort savings are readily apparent when compared to using
these smaller devices.
For a nonblocking crosspoint, the number of points required is
the product of the number of inputs multiplied by the number
of outputs. Nonblocking requires that the programming of a
given input to one or more outputs does not restrict the
availability of that input to be a source for any other outputs.
Some nonblocking crosspoint architectures require more than this
minimum as previously calculated. In addition, there are blocking
architectures that can be constructed with fewer devices than this
minimum. These systems have connectivity available on a statistical
basis that is determined when designing the overall system.
The basic concept in constructing larger crosspoint arrays is to
connect inputs in parallel in a horizontal direction and to wire-OR
the outputs together in the vertical direction. The meaning of
horizontal and vertical can best be understood by looking at a
diagram. Figure 30 illustrates this concept for a 32 × 32 crosspoint
array that uses four ADV3205 devices. Note that the 75 Ω source
terminations are not shown on the outputs, but they are required
when driving the 75 Ω transmission lines.
ADV3205
ADV3205
IN00 TO IN15
IN16 TO IN31
ADV3205
ADV3205
16
16
16
16
75Ω
75Ω
16
16
16
8
16
16
Figure 30. 32 × 32 Crosspoint Array Using Four ADV3205 Devices



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com