| Electronic Components Datasheet Search |
|
06XS3517 Datasheet(PDF) 21 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
06XS3517 Datasheet(HTML) 21 Page - Freescale Semiconductor, Inc |
|
21 / 41 page ![]() Analog Integrated Circuit Device Data Freescale Semiconductor 21 06XS3517 FUNCTIONAL DEVICE OPERATION OPERATION MODES FUNCTIONAL DEVICE OPERATION OPERATION MODES SLEEP MODE The Sleep mode is the default mode of the 06XS3517. This is the state of the device after first applying battery voltage (VBAT) and prior to any I/O transitions. This is also the state of the device when IGN, FOG, FLASHER, and RSTB are logic [0] (wake=0). In the Sleep mode, the outputs and all internal circuitry are OFF to minimize current draw. In addition, all SPI-configurable features of the device are reset. The 06XS3517 will transit to two modes (Normal and Fail) depending on wake and fail signals (see Fig13). The transition to the other modes is according following signals: • Wake = IGN or IGN_ON or FLASHER or FLASHER_ON or RSTB or FOG or FOG_ON • Fail = VCC fail or SPI fail or External limp NORMAL MODE The 06XS3517 is in Normal mode when: • Wake = 1 • Fail = 0 In Normal operating mode the power outputs are under full control of the SPI as follows: • The outputs 1 to 6, including multiphase timing and selectable slew-rate, are controlled by the programmable PWM module. • The outputs 1 to 5 are switched OFF in case of an under-voltage on VBAT. • The outputs 1 to 5 are protected by the selectable over- current double window and over-temperature shutdown circuit. • The digital diagnosis feature transfers status of the smart outputs via SPI. • The analog current sense output (current recopy feature) can be routed by SPI. • The outputs 1 and 5 can be configured to control LED loads. • The SPI reports NM=1 in this mode. The figure below describes the PWM, outputs and over- current behavior in Normal mode. FAIL MODE The 06XS3517 is in Fail mode when: • Wake = 1 • Fail = 1. In Fail mode: • The outputs are under control of external pins (see Table 6) • The outputs are fully protected in case of an overload, over-temperature and under-voltage (on VBAT or on VCC). • The SPI reports continuously the content of address 11 (Initialization register), regardless previously requested output data word. • Analog current sense is not available. • Output 2 is configured in Xenon mode. • In case of an overload (OCHI2 or OCLO) conditions or under-voltage on VBAT, the outputs are under control of autorestart feature. • In case of serious overload condition (OCHI1 or OT) the corresponding output is latched OFF until a new wake- up event (wake=0 then 1). Table 6. Output States During Limp Home Over-current Output D0-D6 bits D7 bit Over-current OUT[1,2] IGN (external) IGN_ON 1.4 sec min Output 1 Parking Light Output 2 Low Beam Output 3 High Beam Output 4 Fog Light Output 5 Flasher External Switch Spare IGN Pin IGN Pin OFF FOG Pin FLASHER Pin OFF |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |