34063AD datasheet(2/2 Pages) SLS

2 / 2 page

System Logic

Semiconductor

SLS

SL34063A

ORDERING INFORMATION

Device

Temperature Range Package

34063AD 0° to +70°C

SO-8

34063AP1

Plastic DIP

ELECTRICAL CHARACTERICISTICS

(VCC = 5.0 V, TA= 0 to +70

oC unless otherwise specified.)

Characteristics

Symbol

Min

Typ

Max

Unit

OSCILLATOR

Frequency (VPin 5 = 0 V, CT = 1.0 nF, TA = 25°C)

fosc

kHz

Charge Current (VCC = 5.0 V to 40 V, TA = 25°C)

Ichg

µA

Discharge Current (VCC = 5.0 V to 40 V, TA = 25°C)

Idischg

140

200

260

µA

Discharge to Charge Current Ratio (Pin7 to Vcc, TA=25°C) Idischg/Ichg 5.2

6.2

7.5

—

Current Limit Sense Voltage (Ichg = Idischg, TA = 25°C)

Vlpk(sense) 250

300

350

OUTPUT SWITCH (Note 3)

Saturation Voltage, Darlington Connection (ISW = 1.0 A,

Pins 1, 8 connected)

VCE(sat)

—

1.0

1.3

Saturation Voltage (ISW = 1.0 A, RPin 8 = 82

Ω to V

CC.

Forced

β = 20)

VCE(sat)

—

0.45

0.7

DC Current Gain (ISW = 1.0 A, VCE

= 5.0 V, T

A = 25°C)

hFE

120

—

Collector Off-State Current (VCE = 40V)

IC(off)

—

0.01

100

µA

COMPARATOR

Threshold Voltage (TA = 25°C)

(TA = TLOW to THIGH)

Vth

1.225

1.21

1.25

—

1.275

1.29

Threshold Voltage (TA = 25°C) **

Vth

1.2375

1.25

1.2625

Threshold Voltage Line Regulation (VCC = 3 0 V to 40 V)

Regime

1.4

5.0

Input Bias Current (Vin=0V)

IIB

—

-40

-400

TOTAL DEVICE

Supply Current (VCC = 5 0 V to 40 V, CT = 1 0 nF, Vpin7 = VCC.

VPin5 > Vth, Pin 2 = Gnd, Remaining pins open)

ICC

2.5

4.0

NOTES:

1. Maximum package power dissipation limits must be observed.

2.Low duty cycle pulse techniques are used during test to maintain Junction temperature as close to ambient temperature as

possible

3.If the output switch is driven into hard saturation (non Darlington configuration) at low switch currents (< 300 mA) and high

driver currents (>30 mA), it may take up to 2.0

µs to come out of saturation This condition will shorten the off' time at

frequencies > 30 kHz, and is magnified at high temperatures This condition does not occur with a Darlingto n configuration,

since the output switch cannot saturate If a non Darlington configuration is used, the following output drive condition is

recommended

Forced

β of output switch = I

C, output/(Ic, driver -7.0 mA*) > 10

*The 100

Ω. resistor in the emitter of the driver device requires about 7.0 mA before the output switch conducts

**Possible version for shipment

Pin connection

34063AD Datasheet(PDF) 2 Page - System Logic Semiconductor

34063AD Datasheet(HTML) 2 Page - System Logic Semiconductor

Html Pages

1 2

Datasheet Download

Link URL