ST10F276E datasheet(43/235 Pages) STMICROELECTRONICS

43 / 235 page

ST10F276E

Internal Flash memory

Doc ID 12303 Rev 3

43/235

Erase suspend, program and resume

A Sector Erase operation can be suspended in order to program (Word or Double Word)

another sector.

Example: Sector Erase of sector B3F1 of Bank 3 in XFLASH Module.

FCR0H|= 0x0800;/*Set SER in FCR0H*/

FCR1H|= 0x0002;/*Set B3F1*/

FCR0H|= 0x8000;/*Operation start*/

Example: Sector Erase Suspend.

FCR0H|= 0x4000;/*Set SUSP in FCR0H*/

/*Loop to wait for LOCK=0 and WMS=0*/

{tmp1 = FCR0L;

tmp2 = FCR0H;

} while ((tmp1 && 0x0010) || (tmp2 && 0x8000));

Example: Word Program of data 0x5555AAAA at address 0x0C5554 in XFLASH module.

FCR0H&= 0xBFFF;/*Rst SUSP in FCR0H*/

FCR0H|= 0x2000;/*Set WPG in FCR0H*/

FARL = 0x5554; /*Load Add in FARL*/

FARH = 0x000C; /*Load Add in FARH*/

FDR0L = 0xAAAA; /*Load Data in FDR0L*/

FDR0H = 0x5555; /*Load Data in FDR0H*/

FCR0H|= 0x8000; /*Operation start*/

Once the Program operation is finished, the Erase operation can be resumed in the

following way:

FCR0H|= 0x0800;/*Set SER in FCR0H*/

FCR0H|= 0x8000;/*Operation resume*/

Notice that during the Program Operation in Erase suspend, bits SER and SUSP are low. A

Word or Double Word Program during Erase Suspend cannot be suspended.

To summarize:

●

A Sector Erase can be suspended by setting SUSP bit

●

To perform a Word Program operation during Erase Suspend, firstly bits SUSP and

SER must be reset, then bit WPG and WMS can be set

●

To resume the Sector Erase operation bit SER must be set again

●

In any case it is forbidden to start any write operation with SUSP bit already set

Set protection

Example 1: Enable Write Protection of sectors B0F3-0 of Bank 0 in IFLASH module.

FCR0H|= 0x0100;/*Set SPR in FCR0H*/

FARL = 0xDFB4;/*Load Add of register FNVWPIRL in FARL*/

FARH = 0x000E;/*Load Add of register FNVWPIRL in FARH*/

FDR0L = 0xFFF0;/*Load Data in FDR0L*/

FDR0H = 0xFFFF;/*Load Data in FDR0H*/

FCR0H|= 0x8000;/*Operation start*/

Notice that bit SMOD of FCR0H must not be set, since Write Protection bits of IFLASH

Module are stored in Test-Flash (XFLASH Module).

ST10F276E Datasheet(PDF) 43 Page - STMicroelectronics

ST10F276E Datasheet(HTML) 43 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL