AD630A datasheet(2/8 Pages) AD

2 / 8 page

AD630–SPECIFICATIONS

REV. C

–2–

ORDERING GUIDE

Temperature

Package

Model

Ranges

Descriptions

Options

AD630JN

°C to +70°C

Plastic DIP

N-20

AD630KN

°C to +70°C

Plastic DIP

N-20

AD630AD

–25

°C to +85°C Side Brazed DIP D-20

AD630BD

–25

°C to +85°C Side Brazed DIP D-20

AD630SD

–55

°C to +125°C Side Brazed DIP D-20

AD630SD/883B

–55

°C to +125°C Side Brazed DIP D-20

5962-8980701RA –55

°C to +125°C Side Brazed DIP D-20

AD630SE/883B

–55

°C to +125°C LCC

E-20A

5962-89807012A –55

°C to +125°C LCC

E-20A

AD630JCHIPS

°C to +70°C

Chip

AD630SCHIPS

–55

°C to +125°C Chip

(@ + 25 C and

VS =

15 V unless otherwise noted)

Model

AD630J/A

AD630K/B

AD630S

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

Unit

GAIN

Open Loop Gain

110

100

120

110

±1, ±2 Closed Loop Gain Error

0.1

0.05

0.1

Closed Loop Gain Match

0.1

0.05

0.1

Closed Loop Gain Drift

ppm/

°C

CHANNEL INPUTS

VIN Operational Limit

(–VS + 4 V) to (+VS – 1 V)

Volts

Input Offset Voltage

500

100

500

µV

Input Offset Voltage

TMIN to TMAX

800

160

1000

µV

Input Bias Current

100

300

100

300

100

300

Input Offset Current

Channel Separation @ 10 kHz

100

COMPARATOR

VIN Operational Limit

(–VS + 3 V) to (+VS – 1.5 V)

(–VS + 3 V) to (+VS – 1.3 V)

Volts

Switching Window

1.5

Switching Window

TMIN to TMAX

2.0

2.5

Input Bias Current

100

300

100

300

100

300

Response Time (–5 mV to +5 mV Step)

200

Channel Status

ISINK @ VOL = –VS + 0.4 V

1.6

Pull-Up Voltage

(–VS + 33 V)

Volts

DYNAMIC PERFORMANCE

Unity Gain Bandwidth

MHz

Slew Rate4

µs

Settling Time to 0.1% (20 V Step)

µs

OPERATING CHARACTERISTICS

Common-Mode Rejection

105

110

Power Supply Rejection

110

Supply Voltage Range

±16.5

Volts

Supply Current

OUTPUT VOLTAGE, @ RL = 2 k

Ω

TMIN to TMAX

±10

Volts

Output Short Circuit Current

TEMPERATURE RANGES

Rated Performance–N Package

+70

N/A

°C

Rated Performance–D Package

–25

+85

–25

+85

–55

+125

°C

NOTES

1If one terminal of each differential channel or comparator input is kept within these limits the other terminal may be taken to the positive supply.

2These parameters are guaranteed but not tested for J and K grades. For A, B and S grades they are tested.

SINK @ VOL = (–VS + 1) volt is typically 4 mA.

4Pin 12 Open. Slew rate with Pins 12 and 13 shorted is typically 35 V/

µs.

Specifications subject to change without notice.

Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min

and max specifications are guaranteed, although only those shown in boldface are tested on all production units.

ABSOLUTE MAXIMUM RATINGS

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±18 V

Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . . 600 mW

Output Short Circuit to Ground . . . . . . . . . . . . . . . . Indefinite

Storage Temperature, Ceramic Package . . . . –65

°C to +150°C

Storage Temperature, Plastic Package . . . . . . –55

°C to +125°C

Lead Temperature Range (Soldering, 10 sec ) . . . . . . . +300

°C

Max Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150

°C

THERMAL CHARACTERISTICS

20-Pin Plastic DIP (N)

°C/W

20-Pin Ceramic DIP (D)

°C/W

120

°C/W

20-Pin Leadless Chip Carrier (E)

°C/W

120

°C/W

AD630A Datasheet(PDF) 2 Page - Analog Devices

AD630A Datasheet(HTML) 2 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

Datasheet Download

Link URL