| Electronic Components Datasheet Search |
|
AD9731-PCB Datasheet(PDF) 8 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9731-PCB Datasheet(HTML) 8 Page - Analog Devices |
|
8 / 11 page ![]() AD9731 –8– REV. A THEORY AND APPLICATIONS The AD9731 high speed digital-to-analog converter utilizes most significant bit decoding and segmentation techniques to reduce glitch impulse and deliver high dynamic performance on lower power consumption than previous bipolar DAC technologies. The design is based on four main subsections: the decoder/ driver circuits, the edge-triggered data register, the switch net- work and the control amplifier. An internal bandgap reference is included to allow operation of the device with minimum exter- nal support components. Digital Inputs/Timing The AD9731 has TTL/high speed CMOS-compatible single- ended inputs for data inputs and clock. The switching threshold is +1.5 V. In the decoder/driver section, the three MSBs are decoded to seven “thermometer code” lines. An equalizing delay is included for the seven least significant bits and the clock signals. This delay minimizes data skew and data setup and hold times at the register inputs. –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 1 1 1AP 0Hz START 200kHz 2MHz STOP ENCODE = 125MHz AOUT1 = 800kHz AOUT2 = 900kHz SPAN = 2MHz Figure 14. Wideband Intermodulation Distortion F1 = 800 kHz; F2 = 900 kHz; 125 MHz Clock; Span = 2 MHz –10 –20 –30 –40 –50 –60 –70 –80 –90 –100 1 1 1AP 0Hz START 6.25MHz 62.5MHz STOP ENCODE = 125MHz AOUT1 = 800kHz AOUT2 = 900kHz SPAN = 62.5MHz PRN Figure 15. Wideband Intermodulation Distortion F1 = 800 kHz; F2 = 900 kHz; 125 MHz Clock; Span = 62.5 MHz The on-board register is rising-edge triggered and should be used to synchronize data to the current switches by applying a pulse with proper data setup and hold times as shown in the timing diagram. Although the AD9731 is designed to provide isolation of the digital inputs to the analog output, some cou- pling of digital transitions is inevitable. Digital feedthrough can be minimized by forming a low-pass filter at the digital input by using a resistor in series with the capacitance of each digital input. This common high speed DAC application technique has the effect of isolating digital input noise from the analog output. References The internal bandgap reference, control amplifier and reference input are pinned out to provide maximum user flexibility in configuring the reference circuitry for the AD9731. When using the internal reference, REF OUT (Pin 25) should be connected to CONTROL AMP IN (Pin 26). CONTROL AMP OUT (Pin 24) should be connected to REF IN (Pin 23). A 0.1 µF ceramic capacitor connected from Pin 23 to Analog –VS (Pin 22) im- proves settling time by decoupling switching noise from the current sink baseline. A reference current cell provides feedback to the control amplifier by sinking current through RSET (Pin 17). Full-scale current is determined by CONTROL AMP IN and RSET according to the following equation: IOUT (FS) = 32(CONTROL AMP IN/RSET) The internal reference is nominally –1.25 V with a tolerance of ± 8% and typical drift over temperature of 100 ppm/°C. If greater accuracy or temperature stability is required, an external reference can be used. The AD589 reference features 10 ppm/ °C drift over the 0 °C to +70°C temperature range. Two modes of multiplying operation are possible with the AD9731. Signals with bandwidths up to 2.5 MHz and input swings from –0.6 V to –1.2 V can be applied to the CONTROL AMP IN pin as shown in Figure 16. Because the control ampli- fier is internally compensated, the 0.1 µF capacitor discussed above can be reduced to maximize the multiplying bandwidth. However, it should be noted that output settling time, for changes in the digital word, will be degraded. RSET –0.6 TO –1.2V 2.5MHz TYPICAL RT 0.1 F RSET CONTROL AMP IN CONTROL AMP OUT REFERENCE IN AD9731 ANALOG –VS Figure 16. Low Frequency Multiplying Circuit |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |