ADG701/ADG702

–8–

REV. A

APPLICATIONS INFORMATION

The ADG701/ADG702 belongs to Analog Devices’ new fam-

ily of CMOS switches. This series of general purpose switches

have improved switching times, lower on resistance, higher

bandwidth, low power consumption and low leakage currents.

ADG701/ADG702 Supply Voltages

Functionality of the ADG701/ADG702 extends from +1.8 V to

+5.5 V single supply, which makes it ideal for battery powered

instruments, where important design parameters are power

efficiency and performance.

It is important to note that the supply voltage effects the input

signal range, the on resistance and the switching times of the

part. By taking a look at the typical performance characteristics

and the specifications, the effects of the power supplies can be

clearly seen.

Ω over the

temperature range.

On Response vs. Frequency

Figure 7 illustrates the parasitic components that affect the ac

performance of CMOS switches (the switch is shown surrounded

by a box). Additional external capacitances will further degrade

some performance. These capacitances affect feedthrough,

crosstalk and system bandwidth.

S

D

Figure 7. Switch Represented by Equivalent Parasitic

Components

The transfer function that describes the equivalent diagram of

the switch (Figure 7) is of the form (A)s shown below.

A(s)

= R

T

+1

+1

















where:

The signal transfer characteristic is dependent on the switch

zero in the numerator of the transfer function A(s). Because the

switch on resistance is small, this zero usually occurs at high

frequencies. The bandwidth is a function of the switch output

frequency pole corresponding to these capacitances appears in

the denominator of A(s).

pole breakpoint frequency to occur first. Therefore, in order to

maximize bandwidth a switch must have a low input and output

capacitance and low on resistance. The On Response vs. Fre-

quency plot for the ADG701/ADG702 can be seen in Figure 6.

Off Isolation

Off isolation is a measure of the input signal coupled through an

the input signal to the output load, when the switch is off, as

shown in Figure 8.

S

D

Figure 8. Off Isolation Is Affected by External Load Resis-

tance and Capacitance

produced. The typical performance characteristic graph of Fig-

ure 5 illustrates the drop in off-isolation as a function of fre-

quency. From dc to roughly 1 MHz, the switch shows better

than –75 dB isolation. Up to frequencies of 10 MHz, the off

isolation remains better than –55 dB. As the frequency increases,

more and more of the input signal is coupled through to the

output. Off-isolation can be maximized by choosing a switch

and capacitance affect off isolation also, as they contribute to

the coefficients of the poles and zeros in the transfer function of

the switch when open.

A(s)

=

+1













8-Lead

SOIC

(RM-8)

85

4

1

0.122 (3.10)

0.114 (2.90)

0.199 (5.05)

0.187 (4.75)

PIN 1

0.0256 (0.65) BSC

0.122 (3.10)

0.114 (2.90)

SEATING

PLANE

0.006 (0.15)

0.002 (0.05)

0.018 (0.46)

0.008 (0.20)

0.043 (1.09)

0.037 (0.94)

0.120 (3.05)

0.112 (2.84)

0.011 (0.28)

0.003 (0.08)

0.028 (0.71)

0.016 (0.41)

33°

27°

0.120 (3.05)

0.112 (2.84)

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

6-Lead Plastic Surface Mount (SOT-23)

(RT-6)

0.122 (3.10)

0.106 (2.70)

PIN 1

0.118 (3.00)

0.098 (2.50)

0.075 (1.90)

BSC

0.037 (0.95) BSC

1

3

4

5

6

2

0.071 (1.80)

0.059 (1.50)

0.009 (0.23)

0.003 (0.08)

0.022 (0.55)

0.014 (0.35)

10

0

0.020 (0.50)

0.010 (0.25)

0.006 (0.15)

0.000 (0.00)

0.051 (1.30)

0.035 (0.90)

SEATING

PLANE

0.057 (1.45)

0.035 (0.90)