Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com

ZPS-150A & ZPS-200A

J1-1

Enable

J1-2

Output #1 Rtn

ZPS-300A/AP & ZPS-400A/AP

J3-1

Enable

J3-2

Output #1 Rtn

ZPS-150A & ZPS-200A

J1-4

DC Power Good

J1-3

Output #1 Rtn

ZPS-300A/AP & ZPS-400A/AP

J3-4

DC Power Good

J3-3

Output #1 Rtn

ZPS-150A & ZPS200A

J2-2

Output #1 Sense+

J2-1

Output #1 Sense-

ZPS-300A/AP & ZPS-400A/AP

TB2-1

Output #1 Sense+

TB2-2

Output #1 Sense-

AC INPUT (90-264 VAC Continuous Range Except ZPS-300A,

400A which require input jumpers to be set for 115V or 230V)

FUNCTION

ZPS-150A & ZPS-200A

ZPS-300A, 300AP

CONNECTOR

ZPS-400A, 400AP

115V

230V

115V

230V

SPECIFICATIONS: ALL MODELS

INPUT

AC Input: Auto-ranging (ZPS-150A & 200A) or Jumper selectable (ZPS-300 A & 400 A) or

power factor corrected wide range (ZPS-300AP & 400AP)- input for 115 V or 230 Vac,

47-65Hz internally fused with appropriate fuses (6A-10A)

Power Factor: Typical 0.99 for ZPS-300AP & 400AP. Meets EN 61000-3-2.

Inrush: Cold start AC current is less than 70 A peak for one half cycle of applied power at

230 Vac, limited by a thermistor.

Brownout Protection: Holds regulation to 85 Vac.

Hold-up Time: 20 ms @ after removal of power at nominal line and full load.

Efficiency: 70%-75% typical

OUTPUT

Adjustability: Output #1 is adjustable ±5%. Wide range on auxiliary outputs up to 3.3:1

(see table).

Line Load Cross Regulation: ± 0.6% on all outputs, over AC input range and loads within

the ranges specified in the table.

Ripple & Noise: Less than 1% p-p on all outputs.

Remote Sense Compensates for 250 mV total line drop. Open sense lead protection.

Temperature Coefficient: 0.03% per degree C.

Stability: 0.1% over 8 hours after 30 minutes warm up.

Transient Response: Output voltage returns to within 1% in less than 500 µSec for a 25%

load change. Peak transient does not exceed 3%.

Overload Protection: All outputs protected against short circuit. Input cycling off/on is

required to reset latched-off protection mode.

Overvoltage Protection (Output #1): Protects against power supply induced overvoltage.

Trip point is factory set so that the output does not exceed 6.4 V.

Peak output Current: Peak current should be limited to a maximum of 15 seconds.

Enable: TTL level ”0” or contact closure to the ve-sense line inhibits DC outputs.

DC Power Good: Provides a TTL level “1” when output #1 is above 4.6 V nominal.

ENVIRONMENTAL

Thermal Protection: Automatic shutdown if power supply temperature exceeds 90° C.

Temperature Range: 0° C to 40° C at full ratings. Output power linearly derated by 1.7%

per deg. C over 50° C to 70° C.

Safety Agencies: UL 1950, CSA C 22.2 234 level 5, VDE 0805 /EN 60950, CE marking to low

voltage directive.

Conducted EMI: All models except ZPS-300AP, meet FCC Part 15 Subpart J, Class B, VDE

0871/B, EN 55022/B. ZPS-300AP meets Class A.

Output Isolation: Isolated from ground at 50 Vdc.

Cooling: 5 CFM ZPS-150, 15 CFM ZPS-200, 25 CFM ZPS-300 & 300AP, 30 CFM ZPS-400,

35 CFM ZPS-400AP. Forced air required to achieve full ratings.

OPTIONS:

Option “C”: Available with an enclosed cover

Option “M”: Intended for MEDICAL APPLICATIONS Approved to UL 544, IEC 601/VDE 0750

safety and MDS-201-0004 EMI. Leakage Current is less than 500 µA.

Option “AP”: For 300 watt and 400 watt power supplies, Power Factor corrected.

Consult factory for other available options.

FUNCTION

MODEL

LOCATION

NOTES

CONNECTOR

Output #1

ZPS-150A & ZPS-200A

TB2-1

4.75V-5.25V

TB-22

Rtn (Isolated)

ZPS-300A/AP & 400A/AP

TB4-1

4.75V-5.25V

TB4-2

Rtn (Isolated)

Output #2

ZPS-150A & ZPS-200A

TB3-1

11.5V-25.2V

TB3-2

Rtn (Isolated)

ZPS-300A/AP & 400A/AP

TB2-3

11.5V-25.2V

TB2-4

Rtn (Isolated)

Output #3

ZPS-150A & ZPS-200A

TB3-3

9.5V-15.8V

TB3-4

Rtn (Isolated)

ZPS-300A/AP & 400A/AP

TB2-5

4.75V-15.8V

TB2-6

Rtn (Isolated)

Output #4

ZPS-150A & ZPS-200A

TB3-5

4.75V-12.6V

TB3-6

Rtn (Isolated))

ZPS-300A /AP & 400A/AP

TB2-7

4.75V-15.8V

TB2-8

Rtn (Isolated)

DC OUTPUT

Barrier strip

#6-32 screws

0.375”

centers

FUNCTION

MODEL

LOCATION

NOTES

CONNECTOR

STATUS AND CONTROL

Enable

DC Power

Good

Remote

Sense

Dimensions:

Inches

Millimeters

TB1-(1)

TB1-(2)

TB1-(3)

Bus bars

#8-32 screws

Barrier Strip

#6-32 Screws

.375” centers

Neutral

Line 2

Line

Line 1

Line

Line 1

Neutral

Line 2

Safety Ground

Safety Ground

Molex Part #

22-23-2041

Mates with

Molex Part #

22-01-3047

Molex Part #

22-23-2021Mates

with 22-01-3027

Barrier Strip #

6-32 Screws

.375” Centers

ZPS-150A, 200A

4.0 lbs - 1.8 kgs

ZPS-250A, 250AP, 300A, 300AP

5.0 lbs - 2.3 kgs

ZPS-400A, 400AP

7.0 lbs - 3.2 kgs

150, 200 WATTS

300, 400 WATTS (PFC AVAILABLE)

11”x 5”x 2.5”

13”x 6”x 2.5”

ZPS-150A, 200A, 250A, 300A

ZPS-400A