| Electronic Components Datasheet Search |
|
5767154-3 Datasheet(PDF) 2 Page - Tyco Electronics |
|
|
|||||||||||||||||||||||||||||
5767154-3 Datasheet(HTML) 2 Page - Tyco Electronics |
|
2 / 7 page ![]() 408-10040 PIDG STRATO-THERM Terminal Crimping Tools Rev C 2 of 7 Tyco Electronics Corporation HAND TOOL WIRE DOT HANDLE COLOR TERMINAL COLOR CODE STRIP LENGTH PART NUMBER SIZE (AWG) DOT CODE HANDLE COLOR CODE HIGH TEMP. LOW TEMP. Min. Max. 576778 24-22 2 Dots 1 Handle Black 1 Handle Brown Brown Black 5.56 [.219] 6.35 [.250] 576779 20 1 Dot 1 Handle Gray 1 Handle Purple Gray Purple (With Black Stripe) 5.56 [.219] 6.35 [.250] 576780 18 2 Dots 1 Handle Orange 1 Handle Black Orange Orange (With Black Stripe) 5.56 [.219] 6.35 [.250] 576781 16 1 Dot 2 Handles Orange Orange Orange (With Black Stripe) 5.56 [.219] 6.35 [.250] 576782 14 2 Dots 1 Handle White 1 Handle Black White White (With Black Stripe) 5.56 [.219] 6.35 [.250] 576783 12 1 Dot 2 Handles White White White (With Black Stripe) 5.56 [.219] 6.35 [.250] 576784 10 1 Dot 2 Handles Black Black --- 7.62 [.300] 8.38 [.330] Figure 2 3. CRIMPING PROCEDURE Refer to Section 5 for information on the insulation crimp adjustment. Refer to Figure 3 and the following steps for terminal crimping procedures. Figure 3 PIDG STRATO-THERM Terminals Locator Wire Barrel Butts Against Locator End of Conductor Butts Against Locator Insulation Barrel Wire Barrel 1. Strip the wire to the dimension provided in Figure 2, being careful to avoid nicking or damaging the conductor(s). Do NOT use wire with nicked or missing conductors. Make sure terminal insulation color code matches tool handle color. 2. Open the tool jaws by closing the tool handles until the ratchet releases, then allow the handles to open fully. 3. Place the terminal in the dies so that the wire barrel butts against the locator. 4. Close the tool handles until the terminal is held firmly in place. Do NOT deform the terminal. 5. Insert properly stripped wire into the terminal until the end of the conductor butts against the locator. Do NOT allow wire insulation to enter the terminal wire barrel. 6. Complete the crimp by closing the tool handles until the ratchet releases. 7. Release the tool handles, allow the handles to open fully, and remove the crimped terminal. 8. Observe the dot code on the finished crimp to ensure that the correct terminal and tool combination was used. See Figure 2. 9. Refer to Section 4 and Figure 4 for terminal crimp inspection procedure. NOTE i CAUTION ! NOTE i CAUTION ! |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |