DJ (ADJ)

ASCTB176E 201202-T

RATING

1. Coil data

1) Single side stable

2) 1 coil latching

3) 2 coil latching

2. Specifications

Notes: *1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the

actual load.

*2. Wave is standard shock voltage of

±1.2×50µs according to JEC-212-1981

*3. In order to obtain the full rated life cycles, the relay should be properly vented by removing the vent nib. More detail, please look at caution for NOTES.

*4. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage

conditions in NOTES.

Nominal coil voltage

Pick-up voltage

(at 20

Drop-out voltage

(at 20

Coil resistance

[

Nominal operating power

Max. applied voltage

(at 20

5V DC

75%V or less of nominal

voltage (Initial)

10%V or more of nominal

voltage (Initial)

100

Ω

250mW

130%V of nominal voltage

6V DC

144

Ω

12V DC

576

Ω

24V DC

2,304

Ω

48V DC

9,216

Ω

Nominal coil voltage

Set voltage

(at 20

Reset voltage

(at 20

Coil resistance

[

Nominal operating power

Max. applied voltage

(at 20

5V DC

70%V or less of nominal

voltage (Initial)

70%V or less of nominal

voltage (Initial)

167

Ω

150mW

130%V of nominal voltage

6V DC

240

Ω

12V DC

960

Ω

24V DC

3,840

Ω

48V DC

15,360

Ω

Nominal coil voltage

Set voltage

(at 20

Reset voltage

(at 20

Coil resistance

[

Nominal operating power

Max. applied voltage

(at 20

5V DC

70%V or less of nominal

voltage (Initial)

70%V or less of nominal

voltage (Initial)

100

Ω

250mW

130%V of nominal voltage

6V DC

144

Ω

12V DC

576

Ω

24V DC

2,304

Ω

48V DC

9,216

Ω

Characteristics

Item

Specifications

Contact

Arrangement

1 Form C, 1 Form A, 1 Form B, 1 Form A 1 Form B, 2 Form C, 2 Form A, 2 Form B

Contact resistance (Initial)

Max. 100 m

Ω (By voltage drop 6 V DC 1A)

Contact material

Rating

Nominal switching capacity (resistive load)

16 A 250V AC (1 Form C, 1 Form A, 1 Form B),

10 A 250V AC (2 Form C, 2 Form A, 2 Form B, 1 Form A 1 Form B)

Max. switching power (resistive load)

4,000 V A

Max. switching voltage

250V AC

Max. switching current

16 A (1 Form C, 1 Form A, 1 Form B),

10 A (1 Form A 1 Form B, 2 Form C, 2 Form A, 2 Form B)

Nominal operating power

150mW (1 coil latching), 250mW (Single side stable, 2 coil latching)

100mA 5 V DC

Electrical

characteristics

Insulation resistance (Initial)

Min. 1,000M

Ω (at 500V DC) Measurement at same location as “Breakdown voltage” section.

Breakdown voltage

(Initial)

Between open contacts

1,000 Vrms for 1min. (Detection current: 10mA.)

Between contact and coil

4,000 Vrms for 1min. (Detection current: 10mA.)

Surge breakdown

Between contact and coil

Min. 10,000 V

Temperature rise (coil) (at 70

Max. 55

°C (By resistive method, nominal voltage applied to the coil, max. switching current.)

Operate time [Set time] (at 20

Max. 20 ms [20 ms] (Nominal voltage applied to the coil, excluding contact bounce time.)

Release time [Reset time] (at 20

Max. 20 ms [20 ms] (Nominal voltage applied to the coil, excluding contact bounce time.)

Mechanical

characteristics

Shock resistance

Functional

µs.)

Destructive

Vibration resistance

Functional

10 to 55 Hz at double amplitude of 2 mm (Detection time: 10

µs.)

Destructive

10 to 55 Hz at double amplitude of 3 mm

Expected life

Mechanical

Min. 5

Conditions

Ambient temperature: –40

Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)

Unit weight