VMV3 datasheet(94/212 Pages) MICROSEMI

94 / 212 page

Military ProASIC3/EL DC and Switching Characteristics

2-80

Revision 3

HSTL Class I

High-Speed Transceiver Logic is a general-purpose high-speed 1.5 V bus standard (EIA/JESD8-6).

Military ProASIC3E devices support Class I. This provides a differential amplifier input buffer and a push-

pull output buffer.

Timing Characteristics

Table 2-135 • Minimum and Maximum DC Input and Output Levels

HSTL Class I

VIL

VIH

VOL

VOH

IOL IOH IOSL

IOSH

IIL1 IIH2

Drive

Strength

Min.

Max.

Min.

Max.

Min.

VmA mA

Max.

mA3

Max.

mA3

µA4 µA4

8 mA

–0.3 VREF – 0.1 VREF + 0.1

3.6

0.4

VCCI – 0.4

15 15

Notes:

1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 V < VIN < VIL.

2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is

larger when operating outside recommended ranges.

3. Currents are measured at 100°C junction temperature and maximum voltage.

4. Currents are measured at 125°C junction temperature.

Figure 2-20 • AC Loading

Table 2-136 • AC Waveforms, Measuring Points, and Capacitive Loads

Input Low (V)

Input High (V)

Measuring Point*

(V)

VREF (typ.) (V)

VTT (typ.) (V)

CLOAD (pF)

VREF – 0.1

VREF + 0.1

0.75

Note:

*Measuring point = Vtrip. See Table 2-28 on page 2-27 for a complete table of trip points.

Test Point

20 pF

HSTL

Class I

VTT

Table 2-137 • HSTL Class I

Military-Case Conditions: TJ = 125°C, Worst-Case VCC = 1.14 V,

Worst-Case VCCI = 1.4 V, VREF = 0.75 V

Applicable to Pro I/Os for A3PE600L and A3PE3000L Only

Speed

Grade

tDOUT

tDP

tDIN

tPY

tEOUT

tZL

tZH

tLZ

tHZ

tZLS

tZHS

Units

Std.

0.80

3.15

0.05

2.76

0.52

3.20

3.11

–

5.41

5.32

–1

0.68

2.68

0.05

2.34

0.44

2.73

2.65

–

4.60

4.52

Note:

For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.

Table 2-138 • HSTL Class I

Military-Case Conditions: TJ = 125°C, VCC = 1.425 V,

Worst-Case VCCI = 1.4 V, VREF = 0.75 V

Applicable to Pro I/Os for A3PE600L and A3PE3000L Only

Speed

Grade

tDOUT

tDP

tDIN

tPY

tEOUT

tZL

tZH

tLZ

tHZ

tZLS

tZHS

Units

Std.

0.61

3.02

0.04

2.52

0.40

3.05

3.00

–

4.51

4.46

–1

0.52

2.57

0.03

2.14

0.34

2.59

2.55

–

3.84

3.79

Note:

For specific junction temperature and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.

VMV3 Datasheet(PDF) 94 Page - Microsemi Corporation

VMV3 Datasheet(HTML) 94 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL