ADV601JS datasheet(17/52 Pages) AD

17 / 52 page

ADV601

–17–

REV. 0

DRAM Interface Pins

Name

Pins

I/O

Description

DDAT[15:0]

I/O

DRAM Data Bus. The ADV601 uses these pins for 16-bit data read/write

operations to the external 256K

× 16-bit DRAM. (The operation of the DRAM

interface is fully automatic and controlled by internal functionality of the

ADV601.) These pins are compatible with 30 pF loads.

DADR[8:0]

DRAM Address Bus. The ADV601 uses these pins to form the multiplexed

row/column address lines to the external DRAM. (The operation of the DRAM

interface is fully automatic and controlled by internal functionality of the

ADV601.) These pins are compatible with 30 pF loads.

RAS

DRAM Row Address Strobe. This pin is compatible with 30 pF loads.

CAS

DRAM Column Address Strobe. This pin is compatible with 30 pF loads.

DRAM Write Enable. This pin is compatible with 30 pF loads.

Note that the ADV601 does not have a DRAM

OE pin. Tie the DRAM’s OE

pin to ground.

Serial Port Pins and Timing

DSP Interface Pins

Name

Pins

I/O

Description

TXD

Serial Transmit Data. Connect this pin to an optional, external DSP’s serial

interface RXData pin. If no DSP is present, this pin may be left unconnected.

This pin is compatible with 30 pF loads.

The TXD pin is for serial data output from the ADV601. Serial data consists of

16-bit words that are transferred most-significant-bit first.

Note that the Mode Control register must be set to indicate whether or not the

external DSP is present.

RXD

Serial Receive Data. Connect this pin to an optional, external DSP’s serial

interface TXData pin. If no DSP is present, tie this pin to ground. This pin is

compatible with 30 pF loads.

The RXD pin is for serial data input to the ADV601. Serial data consists of 16-

bit words that are transferred most-significant-bit first.

Note that the Mode Control register must be set to indicate whether or not the

external DSP is present.

TCLK

Serial Data Clock (VCLK/4). Connect this pin to an optional, external DSP’s

serial interface SCLK pin. If no DSP is present, this pin may be left uncon-

nected. This pin is compatible with 30 pF loads.

The TCLK pin is the serial interface clock. Communication in and out of the

ADV601 requires bits of data to be transmitted after a rising edge of TCLK, and

sampled on a falling edge of TCLK. The DSP must be in external bit clock mode

to use TCLK correctly. The codec drives the TCLK frequency at 1/4 VCLK.

Some typical VCLK and TCLK frequencies are as follows:

•

VCLK

TCLK (= 1/4 VCLK)

•

27 MHz

6.75 MHz

•

29.5 MHz

7.375 MHz

•

24.54 MHz

6.135 MHz

Note that the Mode Control register must be set to indicate whether or not the

external DSP is present.

ADV601JS Datasheet(PDF) 17 Page - Analog Devices

ADV601JS Datasheet(HTML) 17 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

Datasheet Download

Link URL