STM32F407IG datasheet(35/167 Pages) STMICROELECTRONICS

35 / 167 page

STM32F405xx, STM32F407xx

Description

Doc ID 022152 Rev 2

35/167

The USB OTG HS peripheral is compliant with the USB 2.0 specification and with the OTG

1.0 specification. It has software-configurable endpoint setting and supports

suspend/resume. The USB OTG full-speed controller requires a dedicated 48 MHz clock

that is generated by a PLL connected to the HSE oscillator.

The major features are:

●

Combined Rx and Tx FIFO size of 1 Kbit × 35 with dynamic FIFO sizing

●

Supports the session request protocol (SRP) and host negotiation protocol (HNP)

●

6 bidirectional endpoints

●

12 host channels with periodic OUT support

●

Internal FS OTG PHY support

●

External HS or HS OTG operation supporting ULPI in SDR mode. The OTG PHY is

connected to the microcontroller ULPI port through 12 signals. It can be clocked using

the 60 MHz output.

●

Internal USB DMA

●

HNP/SNP/IP inside (no need for any external resistor)

●

for OTG/Host modes, a power switch is needed in case bus-powered devices are

connected

2.2.31

Digital camera interface (DCMI)

The camera interface is not available in STM32F405xx devices.

STM32F407xx products embed a camera interface that can connect with camera modules

and CMOS sensors through an 8-bit to 14-bit parallel interface, to receive video data. The

camera interface can sustain a data transfer rate up to 54 Mbyte/s at 54 MHz. It features:

●

Programmable polarity for the input pixel clock and synchronization signals

●

Parallel data communication can be 8-, 10-, 12- or 14-bit

●

Supports 8-bit progressive video monochrome or raw bayer format, YCbCr 4:2:2

progressive video, RGB 565 progressive video or compressed data (like JPEG)

●

Supports continuous mode or snapshot (a single frame) mode

●

Capability to automatically crop the image

2.2.32

Random number generator (RNG)

All STM32F405xx and STM32F407xx products embed an RNG that delivers 32-bit random

numbers generated by an integrated analog circuit.

2.2.33

General-purpose input/outputs (GPIOs)

Each of the GPIO pins can be configured by software as output (push-pull or open-drain,

with or without pull-up or pull-down), as input (floating, with or without pull-up or pull-down)

or as peripheral alternate function. Most of the GPIO pins are shared with digital or analog

alternate functions. All GPIOs are high-current-capable and have speed selection to better

manage internal noise, power consumption and electromagnetic emission.

The I/O configuration can be locked if needed by following a specific sequence in order to

avoid spurious writing to the I/Os registers.

Fast I/O handling allowing maximum I/O toggling up to 84 MHz.

STM32F407IG Datasheet(PDF) 35 Page - STMicroelectronics

STM32F407IG Datasheet(HTML) 35 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL