MLM311P datasheet(4/30 Pages) TI

4 / 30 page

LM111-N, LM211-N, LM311-N

SNOSBJ1E – MAY 1999 – REVISED MARCH 2013

www.ti.com

Absolute Maximum Ratings for the LM111-N/LM211-N

(1) (2)

Total Supply Voltage (V84)

36V

Output to Negative Supply Voltage (V74)

50V

Ground to Negative Supply Voltage (V14)

30V

Differential Input Voltage

±30V

Input Voltage(3)

±15V

Output Short Circuit Duration

10 sec

Operating Temperature Range

LM111-N

−55°C to 125°C

LM211-N

−25°C to 85°C

Lead Temperature (Soldering, 10 sec)

260°C

Voltage at Strobe Pin

V+

−5V

Soldering Information

Dual-In-Line Package

Soldering (10 seconds)

260°C

Small Outline Package

Vapor Phase (60 seconds)

215°C

Infrared (15 seconds)

220°C

ESD Rating(4)

300V

(1)

Refer to RETS111X for the LM111H, LM111J and LM111J-8 military specifications.

(2)

If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and

specifications.

(3)

This rating applies for ±15 supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is

equal to the negative supply voltage or 30V below the positive supply, whichever is less.

(4)

Human body model, 1.5 k

Ω in series with 100 pF.

Electrical Characteristics

(1) for the LM111-N and LM211-N

Parameter

Conditions

Min

Typ

Max

Units

Input Offset Voltage(2)

TA=25°C, RS≤50k

0.7

3.0

Input Offset Current

TA=25°C

4.0

Input Bias Current

TA=25°C

100

Voltage Gain

TA=25°C

200

V/mV

Response Time(3)

TA=25°C

200

Saturation Voltage

VIN≤−5 mV, IOUT=50 mA

0.75

1.5

TA=25°C

Strobe ON Current(4)

TA=25°C

2.0

5.0

Output Leakage Current

VIN≥5 mV, VOUT=35V, TA=25°C,

0.2

ISTROBE=3 mA

Input Offset Voltage(2)

RS≤50 k

4.0

Input Offset Current(2)

Input Bias Current

150

Input Voltage Range

V+=15V, V−=

−15V, Pin 7 Pull-Up

−14.5

13.8-14.7

13.0

May Go To 5V

Saturation Voltage

V+

≥4.5V, V−=0, VIN≤−6 mV,

0.23

0.4

IOUT≤8 mA

Output Leakage Current

VIN≥5 mV, VOUT=35V

0.1

0.5

μA

Positive Supply Current

TA=25°C

5.1

6.0

Negative Supply Current

TA=25°C

4.1

5.0

(1)

These specifications apply for VS=±15V and Ground pin at ground, and −55°C≤TA≤+125°C, unless otherwise stated. With the LM211-N,

however, all temperature specifications are limited to

−25°C≤TA≤+85°C. The offset voltage, offset current and bias current specifications

apply for any supply voltage from a single 5V supply up to ±15V supplies.

(2)

The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a

1 mA load. Thus, these parameters define an error band and take into account the worst-case effects of voltage gain and RS.

(3)

The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.

(4)

This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not

short the strobe pin to ground; it should be current driven at 3 to 5 mA.

Submit Documentation Feedback

Product Folder Links: LM111-N LM211-N LM311-N

MLM311P Datasheet(PDF) 4 Page - Texas Instruments

MLM311P Datasheet(HTML) 4 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Datasheet Download

Link URL