Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load No-Load

G101E

5

4.5 - 5.5

286

30

5.0

200.0

20.0

15

70

500

G102E

5

4.5 - 5.5

256

30

9.0

111.0

12.0

15

78

500

G103E

5

4.5 - 5.5

256

30

12.0

83.0

9.0

15

78

500

G104E

5

4.5 - 5.5

250

30

15.0

67.0

7.0

15

80

500

G105E

5

4.5 - 5.5

278

30

±5.0

±100.0

±10.0

15

72

500

G106E

5

4.5 - 5.5

260

30

±9.0

±56.0

±6.0

15

77

500

G107E

5

4.5 - 5.5

253

30

±12.0

±42.0

±5.0

15

79

500

G108E

5

4.5 - 5.5

250

30

±15.0

±33.0

±4.0

15

80

500

G111E

12

10.8 - 13.2

117

15

5.0

200.0

20.0

15

71

200

G112E

12

10.8 - 13.2

109

15

9.0

111.0

12.0

15

76

200

G113E

12

10.8 - 13.2

107

15

12.0

83.0

9.0

15

78

200

G114E

12

10.8 - 13.2

105

15

15.0

67.0

7.0

15

79

200

G115E

12

10.8 - 13.2

116

15

±5.0

±100.0

±10.0

15

72

200

G116E

12

10.8 - 13.2

107

15

±9.0

±56.0

±6.0

15

78

200

G117E

12

10.8 - 13.2

105

15

±12.0

±42.0

±5.0

15

79

200

G118E

12

10.8 - 13.2

107

15

±15.0

±33.0

±4.0

15

78

200

G121E

24

21.6 - 26.4

57

8

5.0

200.0

20.0

15

73

100

G122E

24

21.6 - 26.4

53

8

9.0

111.0

12.0

15

78

100

G123E

24

21.6 - 26.4

53

8

12.0

83.0

9.0

15

78

100

G124E

24

21.6 - 26.4

52

8

15.0

67.0

7.0

15

79

100

G125E

24

21.6 - 26.4

57

8

±5.0

±100.0

±10.0

15

73

100

G126E

24

21.6 - 26.4

52

8

±9.0

±56.0

±6.0

15

79

100

G127E

24

21.6 - 26.4

52

8

±12.0

±42.0

±5.0

15

80

100

G128E

24

21.6 - 26.4

52

8

±15.0

±33.0

±4.0

15

80

100

Derating Curve

Model Selection Guide

Mechanical Dimensions

Notes:

Notes:

1. Output load regulation is specified for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load. Operation at no-load

may cause damage to the unit.

3. These converters will operate without external components. However, when measuring output

ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the

-Vout pin for single output

units and from each out-

put to common for dual

output units. An input

capacitor will enhance

stability over temperature

and input line variations.

Recommended capacitor

values are given in the

table above. For applica-

tions requiring very low output noise levels, a simple LC filter should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this,

connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output

common.

5. It is recommended that a fuse be used on the input of a power supply for protection. See the

Model Selection table above for the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7 µF

5 VDC 10.0 µF

4.7 µF

12 VDC

2.2 µF

9 VDC

4.7 µF

2.2 µF

24 VDC

1.0 µF

12 VDC 2.2 µF

1.0 µF

15 VDC 1.0 µF

0.47 µF

Other input/output combinations are available

(i.e. 3.3 VDC). Contact the factory for details at:

sales@micropowerdirect.com

Pin

Single

Dual

Pin

Single

Dual

1

-Vin

-Vin

9

+Vout

+Vout

7

NC

NC

11

No Pin

-Vout

8

-Vout

Common

14

+Vin

+Vin

NC = No Connection

Pin Connections

MicroPower Direct

We Power Your Success - For Less!

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

www.micropowerdirect.com