| Electronic Components Datasheet Search |
|
SN75175D Datasheet(PDF) 2 Page - Motorola, Inc |
|
|
|||||||||||||||||||||||||||||
SN75175D Datasheet(HTML) 2 Page - Motorola, Inc |
|
2 / 8 page ![]() SN75175 2 MOTOROLA ANALOG IC DEVICE DATA ELECTRICAL CHARACTERISTICS (Unless otherwise noted, minimum and maximum limits apply over recommended temperature and power supply voltage ranges. Typical values are for TA = 25°C, VCC = 5.0 V, and VICM = 0 V, Note 1.) Characteristic Symbol Min Typ Max Unit Differential Input Threshold Voltage (Note 2) (–12 V p VICM p 12 V, VIH = 2.0 V) (IO = –0.4 mA, VOH q 2.7 V) (IO = 16 mA, VOL p 0.5 V) VTH(D) – – – – 0.2 –0.2 V Input Hysteresis VT+ – VT– – 50 – mV Input Line Current (Differential Inputs) (Unmeasured Input at 0 V, Note 3) (VI = 12 V) (VI = –7.0 V) II – – – – 1.0 –0.8 mA Input Resistance (Note 4) ri 1 Unit Load – – Input Balance and Output Level (Note 3) (–12 V p VICM p 12 V, VIH = 2.0 V) (IO = –0.4 mA, VID = 0.2 V) (IO = 8.0 mA, VID = –0.2 V) (IO = 16 mA, VID = –0.2 V) VOH VOL VOL 2.7 – – – – – – 0.45 0.5 V Input Voltage – High Logic State (Three–State Control) VIH 2.0 – – V Input Voltage – Low Logic State (Three–State Control) VIL – – 0.8 V Input Current – High Logic State (Three–State Control) (VIH = 2.7 V) (VIH = 5.5 V) IIH – – – – 20 100 µA Input Current – Low Logic State (Three–State Control) (VIL = 0.4 V) IIL – – –100 µA Input Clamp Diode Voltage (Three–State Control) (IIK = –18 mA) VIK – – –1.5 V Output Third State Leakage Current (VI(D) = 3.0 V, VIL = 0.8 V, VO = 0.4 V) (VI(D) = –3.0 V, VIL = 0.8 V, VO = 2.4 V) IOZ – – – – –20 20 µA Output Short–Circuit Current (Note 5) (VI(D) = 3.0 V, VIH = 2.0 V, VO = 0 V) IOS –15 – –85 mA Power Supply Current (VIL = 0 V) (All Inputs Grounded) ICC – – 70 mA NOTES: 1. All currents into device pins are shown as positive, out of device pins are negative. All voltages referenced to ground unless otherwise noted. 2. Differential input threshold voltage and guaranteed output levels are done simultaneously for worst case. 3. Refer to EIA–485 for exact conditions. Input balance and guaranteed output levels are done simultaneously for worst case. 4. Input resistance should be derived from input line current specifications and is shown for reference only. See EIA–485 and input line current specifications for more specific input resistance information. 5. Only one output at a time should be shorted. SWITCHING CHARACTERISTICS (Unless otherwise noted, VCC = 5.0 V and TA = 25°C.) Characteristic Symbol Min Typ Max Unit Propagation Delay Time – Differential Inputs to Output Output High to Low Output Low to High tPHL(D) tPLH(D) – – 25 25 35 35 ns Propagation Delay Time – Three–State Control to Output Output Low to Third State Output High to Third State Output Third State to High Output Third State to Low tPLZ tPHZ tPZH tPZL – – – – 16 19 11 11 35 35 30 30 ns |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |