OPTOTRONIC is a registered trademark of OSRAM GmbH.

SYLVANIA is a registered trademark of OSRAM SYLVANIA Inc.

SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA Inc.

Specifications subject to change without notice.

Safety Information

1. The LED module itself and all its components shall not be subjected to mechanical stress and assembly

must not damage or destroy conducting paths on the circuit board.

2. Observe correct electrical polarity, incorrect polarity may destroy the light engine. (Depending on the

product, incorrect polarity may lead to emission of red, or no light)

3. Electrostatic Discharge (ESD) precautions shall be incorporated when handling or installing the module.

4. Circuit boards should be attached securely to the intended substrate, but do not over-tighten screws or

rivets. Heavy vibration should be avoided.

5. The module itself is protected against condensation water with a polymeric conformal coating. Supplemen-

tary soldering on any solder pad will destroy the conformal coating and with it protection against water.

6. Modules may be hot to the touch. Use caution when handling.

WARNING: ONLY QUALIFIED PERSONNEL SHOULD PERFORM INSTALLATION.

TO AVOID ELECTRICAL SHOCK OR COMPONENT DAMAGE, DISCONNECT POWER BEFORE

ATTEMPTING INSTALLATION OF THE POWER SUPPLIES AND/OR MODULES.

Failure to install the power supplies and/or LED modules in accordance with the National Electric

Code (NEC), all applicable Federal, State and local electric codes as well as the specific Underwriters

Laboratories (UL) safety standards for the installation, location and application may cause serious

personal injury, death, property damage and/or product malfunction.

Application Notes

1. Single board add-ons are available to adjust length and fine tune light output.

life. Service life (i.e. lumen maintenance) is primarily a function of LED temperature which is to be monitored

on the circuit board at the designated Tc point. A Tc point temperature of 40°C should be sufficient to enable

a service life of 50,000 hours.

70°C.

4. There is no exact prescription to obtaining an appropriate Tc point temperature due to variations in fixture

face area to transfer the heat from the LED module to the surrounding air. The metal surface can be part of

the mass of the sign itself.

7. Loose wires at the end of the module must be capped off with UL Listed wire connectors.

8. Guidelines for proper UL 2108 installation:

– Definition of a UL 2108 listed Low Voltage Lighting System as it pertains to this module includes:

1. A UL Listed Class 2 power supply.

recommended max number of modules listed

3. Heat Sinks if applicable

– Power supply must be mounted, wired, and grounded in accordance with all applicable NEC and

ANSI standards.

– All modular connections on the secondary side of the power supply must be made using SYLVANIA

connectors. If additional wires and/or splice connectors are necessary, wires are to be UL Listed,

minimum 18 AWG, and connectors must be UL Listed, chosen of appropriate size for number of wires

to be connected.

– WARNING: The low voltage secondary circuit shall not be grounded.

This information shall not supersede the requirement to follow all other safety, assembly and any other

instructions listed in this document.

Application Information

United States

OSRAM SYLVANIA

100 Endicott Street

Danvers, MA 01923

Trade

Phone:

1-800-255-5042

Fax:

1-800-255-5043

National Accounts

Phone:

1-800-562-4671

Fax:

1-800-562-4674

OEM/Special Markets

Phone:

1-800-762-7191

Fax:

1-800-762-7192

Display/Optic

Phone:

1-888-677-2627

Fax:

1-800-762-7192

Canada

OSRAM SYLVANIA LTD.

2001 Drew Road

Mississauga, ON L5S 1S4

Trade

Phone:

1-800-263-2852

Fax:

1-800-667-6772

OEM/Special Markets/Display/Optic

Phone:

1-800-265-2852

Fax:

1-800-667-6772

www.sylvania.com