| Electronic Components Datasheet Search |
|
ZXLD1937 Datasheet(PDF) 11 Page - Zetex Semiconductors |
|
|
|||||||||||||||||||||||||||||
ZXLD1937 Datasheet(HTML) 11 Page - Zetex Semiconductors |
|
11 / 16 page ![]() Inductor selection The choice of inductor will depend on available board space as well as required performance. Small value inductors have the advantage of smaller physical size and may offer lower series resistance and higher saturation current compared to larger values. A disadvantage of lower inductor values is that they result in higher frequency switching, which in turn causes reduced efficiency due to switch losses. Higher inductor values can provide better performance at lower supply voltages. However, if the inductance is too high, the output power will be limited by the internal oscillator, which will prevent the coil current from reaching its peak value. This condition will arise whenever the ramp time (ILX(peak) xL/VIN) exceeds the nominal 5 s maximum 'on' time limit for the LX output. The graphs opposite show the ZXLD1937 performance for given inductor values and different manufacturers. Recommended inductor values for the ZXLD1937 are in the range 6.8 Hto22 H. The inductor should be mounted as close to the device as possible with low resistance connections to the LX and VIN pins. Suitable coils for use with the ZXLD1937 are shown in the table below: Part No. L ( H) DCR ( ) ISAT (A) Manufacturer CMD4D11-100MC 10 0.457 0.5 Sumida www.sumida.com DO1608-103 10 0.16 1.1 Coilcraft www.coilcraft.com LQH31CN100 10 1.3 0.23 Murata www.murata.com LB2012Y100MR 10 0.5 0.1 Taiyo Yuden www.t-yuden.co Diode selection The rectifier diode (D1) should be a fast low capacitance schottky diode with low reverse leakage at the working voltage. It should also have a peak current rating above the peak coil current and a continuous current rating higher than the maximum output load current. The table below gives some typical characteristics for diodes that can be used with the ZXLD1937: Diode VF @ 100mA (mV) IFSM (mA) Ic (mA) IR at 30V ( A) Package ZHCS400 300 1000 400 15 SOD323 ZHCS500 300 1000 500 15 SOT23 Layout considerations PCB tracks should be kept as short as possible to minimise ground bounce, and the ground pin of the device should be soldered directly to the ground plane. It is particularly important to mount the coil and the input/output capacitors close to the device to minimise parasitic resistance and inductance, which will degrade efficiency. The FB pin is a high impedance input so PCB track lengths to this should also be kept as short as possible to reduce noise pickup. Excess capacitance from the FB pin to ground should be avoided. ZXLD1937 SEMICO NDUC TORS ISSUE 1 - JULY 2004 11 LAST TIME BUY Closest Alternative is AP5724WUG-7 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |