EAeDIP160-7

Page 13

ELECTRONIC ASSEMBLY reserves

the right to change specifications

without prior notice. Printing and

typographical

errors

reserved.

ALL COMMANDS AT A GLANCE

The built-in intelligence allows an easy creation of your individual screen content. Below mentioned

commands can be used either directly via the serial interface (see page 12) or together with the

selfdefinable macro.

Terminal commands

After

reset

Command

Codes

Remarks

Form feed FF (dec:12)

^L

The contents of the screen are deleted and the cursor is placed at pos. (1,1)

Carriage return CR(13)

^M

Cursor to the beginning of the line on the extreme left

Line feed LF (dec:10)

^J

Cursor 1 line lower, if cursor in last line then scroll

Position cursor

ESC

T

P

C

L

C=column; L=line; origin upper-left corner (1,1)

1,1

Cursor on/off

C

n1

n1=0: Cursor is invisible; n1=1: Cursor flashes;

1

Save cursor position

S

The current cursor position is saved

Restore cursor position

R

The last saved cursor position is restored

Terminal off

A

Terminal display is switched off; outputs are rejected

Terminal on

E

Terminal display is switched on;

On

Output version

ESC

T

V

The version no. is output in the terminal (e.g. "EA eDIP160-7 V1.0 Rev.A")

Output project name

J

The macro project name is output to the terminal (e.g. "init / delivery state")

Output information

ESC

I

The terminal is initialized and deleted; software version, hardware revision, the macro

project name and the CRC-checksum is ouput to the terminal

Display commands (effect the entire display)

after

reset

Command

Codes

Remarks

Set display orientation

ESC

D

O

n1

n1=0: 0°; n1=1: 90°; n1=2: 180°; n1=3: 270°; (0°+180°=160x104; 90°+270°=104x160)

0°

Set display contrast

K

n1

n1=0..40: Set display contrast to n1 (default = 20)

n1='+': increase contrast; n1='-': decrease contrast

20

Set grayscale mode

G

n1

n1=0: grayscale mode ON; flashing is possible

n1=1: grayscale mode OFF; flahing not possible

0

Delete display

ESC

D

L

Delete display contents (all pixels off)

Invert display

I

Invert display contents (invert all pixels)

Fill display

S

Fill display contents (all pixels on)

Switch display off

A

Display contents become invisible but are retained, commands are still possible

Switch display on

E

Display contents become visible again

oN

Show clipboard

C

Show content of clipboard; Standard display outputs are no longer visible

Show normal display

content

N

Normal operation, standard display outputs are visible

Clipboard commands (Buffer for display area)

after

reset

Command

Codes

Remarks

Save display contents

ESC

C

B

The entire contents of the display are copied to the clipboard as an image area

Save area

S

x1

y1

x2

y2

The image area from x1,y1 to x2,y2 is copied to the clipboard

Restore area

R

The image area on the clipboard is copied back to the display

Copy area

K

x1

y1

The image area on the clipboard is copied to x1,y1 in the display

Change / draw rectangular areas

after

reset

Command

Codes

Remarks

Delete area

ESC

R

L

x1

y1

x2

y2

Delete an area from x1,y1 to x2,y2 (all pixels off)

Invert area

I

x1

y1

x2

y2

Invert an area from x1,y1 to x2,y2 (invert all pixels)

Fill area

S

x1

y1

x2

y2

Fill an area from x1,y1 to x2,y2 (all pixels on)

Area with fill pattern

M

x1

y1

x2

y2

n1 Fill an area from x1,y1 to x2,y2 with pattern n1 (always set)

Draw box

O

x1

y1

x2

y2

n1 Draw rectangle from x1,y1 to x2,y2 with pattern n1 (always replace)

Draw frame

R

x1

y1

x2

y2

n1 Draw frame of type n1 from x1,y1 to x2,y2 (always set)

Draw frame box

T

x1

y1

x2

y2

n1 Draw frame box of type n1 from x1,y1 to x2,y2 (always replace)

Straight lines and points

after

reset

Command

Codes

Remarks

Settings

Point size / line thickness

ESC

G

Z

n1

n2

n1 = x-point size (1..15); n2 = y-point size (1..15);

1,1

Link mode

V

n1

Set drawing mode n1: 1=set; 2=delete; 3=inverse

1

Blink attribute

ESC

G

B

n1

n1:0=no blink; 1=on/off; 2=blink inverted; 3=off/on (phase shifted)

0

Gray-scale

n1:0=black solid line; 1=dark gray; 3=light gray (refer to command ESC DG)

Draw lines and points

Draw point

ESC

G

P

x1

y1

Set a point at coordinates x1, y1

Draw straight line

D

x1

y1

x2

y2

Draw a straight line from x1,y1 to x2,y2

Continue straight line

W

x1

y1

Draw a straight line from the last end point to x1,y1

0, 0

Draw rectangle

R

x1

y1

x2

y2

Draw four straight lines as a rectange from x1,y1 to x2,y2