HCPL2502 datasheet(11/16 Pages) HP

11 / 16 page

Package Characteristics

Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified.

Parameter

Sym.

Device

Min.

Typ.*

Max.

Units

Test Conditions

Fig.

Note

Input-Output

VISO

8-Pin DIP

3750

V rms

RH < 50%,

6, 14

Momentary

SO-8

t = 1 min.,

Withstand

TA = 25°C

Voltage**

8-Pin DIP

5000

6, 12,

(Option 020)

II-O

8-Pin DIP

µA

45% RH, t = 5 s,

6, 16

VI-O = 3 kVdc,

TA = 25°C

Input-Output

RI-O

8-Pin DIP

1012

Ω

VI-O = 500 Vdc

Resistance

SO-8

Widebody

1012

1013

TA = 25°C

1011

TA = 100°C

Input-Output

CI-O

8-Pin DIP

0.6

f = 1 MHz

Capacitance

SO-8

Widebody

0.5

0.6

*All typicals at TA = 25°C.

**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output

continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics

Table (if applicable), your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output

Endurance Voltage,” publication number 5963-2203E.

Widebody

5000

Notes:

1. Derate linearly above 70

°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).

Derate linearly above 85

°C free-air temperature at a rate of 0.5 mA/°C (SO-8).

2. Derate linearly above 70

°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).

Derate linearly above 85

°C free-air temperature at a rate of 1.0 mA/°C (SO-8).

3. Derate linearly above 70

°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).

Derate linearly above 85

°C free-air temperature at a rate of 1.1 mW/°C (SO-8).

4. Derate linearly above 70

°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).

Derate linearly above 85

°C free-air temperature at a rate of 2.3 mW/°C (SO-8).

5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF,

times 100.

6. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.

7. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the

common mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode

transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse

signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V).

8. The 1.9 k

Ω load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.

9. The 4.1 k

Ω load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor.

10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.

11. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Agilent guarantees a minimum CTR of 19%.

12. See Option 020 data sheet for more information.

13. Use of a 0.1

µf bypass capacitor connected between pins 5 and 8 is recommended.

14. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage

≥ 4500 V rms for 1 second

(leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN

60747-5-2 Insulation Related Characteristics Table if applicable.

15. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage

≥ 6000 V rms for 1 second

(leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN

60747-5-2 Insulation Related Characteristics Table if applicable.

16. This rating is equally validated by an equivalent ac proof test.

6, 15

HCPL2502 Datasheet(PDF) 11 Page - Agilent(Hewlett-Packard)

HCPL2502 Datasheet(HTML) 11 Page - Agilent(Hewlett-Packard)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Download

Link URL