DG201 datasheet(3/7 Pages) INTERSIL

3 / 7 page

Absolute Maximum Ratings

Thermal Information

V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V

V+ to VD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V

VD to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V

VD to VS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28V

VREF to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33V

VREF to VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30V

VREF to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V

VIN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V

Current (Any Terminal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA

Operating Conditions

Temperature Range

“C” Sufﬁx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC

Thermal Resistance (Typical, Note 1)

θJA (oC/W) θJC (oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . .

N/A

Maximum Junction Temperature

Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150oC

Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Speciﬁcations

TA = 25

oC, V+ = +15V, V- = -15V

PARAMETER

TEST CONDITIONS

“C” SUFFIX

UNITS

0oC

(NOTE 2)

25oC70oC

DYNAMIC CHARACTERISTICS

Turn-ON Time (Note 3), tON

RL =1kΩ,VANALOG = -10V to +10V (Figure 1)

1.0

µs

Turn-OFF Time (Note 3), tOFF

RL =1kΩ,VANALOG = -10V to +10V (Figure 1)

0.5

µs

Charge Injection, Q

Figure 2

20 (Typ)

Off Isolation Rejection Ratio, OIRR

f = 1MHz, RL = 100Ω, CL ≤ 5pF, (Figure 3)

50 (Typ)

Crosstalk (Channel-to-Channel), CCRR

One Channel Off

-50 (Typ)

DIGITAL INPUT CHARACTERISTICS

Input Logic Current, IIN(ON)

VIN = 0.8V (Note 3)

±1

±10

µA

Input Logic Current, IN(OFF)

VIN = 2.4V (Note 3)

±1

±10

µA

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

±15 (Typ)

Drain-Source ON Resistance, rDS(ON)

IS = 10mA, VANALOG = ±10V

100

125

Ω

Channel-to-Channel

rDS(ON) Match, rDS(ON)

30 (Typ)

Ω

Drain OFF Leakage Current, ID(OFF)

VANALOG = -14V to +14V

±5

100

Source OFF Leakage Current, IS(OFF)

VANALOG = -14V to +14V

±5

100

Channel ON Leakage

Current, ID(ON) + IS(ON)

VD = VS = -14V to +14V

±5

200

POWER SUPPLY CHARACTERISTICS

Supply Current, I+ Positive

VIN = 0V or VIN = 5V

2000

1000

2000

µA

Supply Current, I- Negative

2000

1000

2000

µA

NOTES:

2. Typical values are for design aid only, not guaranteed and not subject to production testing.

3. All channels are turned off by high “1” logic inputs and all channels are turned on by low “0” inputs; however 0.8V to 2.4V describes the minimum

range for switching properly. Peak input current required for transition is typically -120

µA.

DG201

DG201 Datasheet(PDF) 3 Page - Intersil Corporation

DG201 Datasheet(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL