DG201ABK datasheet(2/7 Pages) INTERSIL

2 / 7 page

4-2

Absolute Maximum Ratings

Thermal Information

V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V

V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25V

VIN to Ground (Note 1) . . . . . . . . . . . . . . . . . . . (V-) -2V to (V+) +2V

VS or VD to V+ (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . +2 to (V-) -2V

VS or VD to V- (Note 1) . . . . . . . . . . . . . . . . . . . . . . . -2 to (V+) +2V

Current, any Terminal Except S or D . . . . . . . . . . . . . . . . . . . . 30mA

Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA

Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 70mA

Operating Conditions

Temperature Range

“A” Sufﬁx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC

“B” Sufﬁx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25oC to 85oC

“C” Sufﬁx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC

Thermal Resistance (Typical, Note 2)

θJA (oC/W) θJC (oC/W)

CERDIP Package . . . . . . . . . . . . . . . . .

PDIP Package . . . . . . . . . . . . . . . . . . .

100

N/A

SOIC Package . . . . . . . . . . . . . . . . . . .

100

N/A

Maximum Junction Temperature

Ceramic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175oC

Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150oC

Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

1. Signals on VS, VD, or VIN exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings.

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Speciﬁcations

V+ = 15V, V- = -15V, GND = 0V, TA = 25

PARAMETER

TEST CONDITIONS

“A” SUFFIX

“B” AND “C” SUFFIX

UNITS

MIN

(NOTE 3)

TYP

MAX

MIN

(NOTE 3)

TYP

MAX

DYNAMIC CHARACTERISTICS

Turn-ON Time, tON

See Figure 1

480

600

480

Turn-OFF Time, tOFF

See Figure 1

370

450

370

Charge Injection, Q

CL = 1nF, RS = 0, VS = 0V

OFF Isolation, OIRR

VIN = 5V, RL = 75Ω, VS = 2.0V,

f = 100kHz

-70-

Crosstalk (Channel to Channel), CCRR

-90

Source OFF Capacitance, CS(OFF)

f = 140kHz, VIN = 5V, VS = VD = 0V

5.0

Drain OFF Capacitance, CD(OFF)

5.0

Channel ON Capacitance,

CD(ON) +CS(ON)

-16-

DIGITAL INPUT CHARACTERISTICS

Input Current with Voltage High, IIH

VIN = 2.4V

-1.0

-0.0004

-1.0

-0.0004

µA

VIN = 15V

0.003

1.0

0.003

1.0

µA

Input Current with Voltage Low, IIL

VIN = 0V

-1.0

-0.0004

-1.0

-0.0004

µA

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

-15

Drain-Source ON Resistance, rDS(ON)

VD = ±10V, VIN = 0.8V (DG201A)

IS = 1mA, VIN = 2.4V (DG202)

115

175

115

200

Ω

Source OFF Leakage Current, IS(OFF)

VIN = 2.4V

(DG201A)

VIN = 0.8V

(DG202)

VS = 14V, VD = -14V

0.01

1.0

0.01

5.0

VS = -14V, VD = 14V

-1.0

-0.02

-5.0

-0.02

Drain OFF Leakage Current, ID(OFF)

VS = -14V, VD = 14V

0.01

1.0

0.01

5.0

VS = 14V, VD = -14V

-1.0

-0.02

-5.0

-0.02

DG201A, DG202

DG201ABK Datasheet(PDF) 2 Page - Intersil Corporation

DG201ABK Datasheet(HTML) 2 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL