HIP2106IP datasheet(3/8 Pages) INTERSIL

3 / 8 page

Absolute Maximum Ratings

Thermal Information

Supply Voltage, VDD, VHB-VHS . . . . . . . . . . . . . . . . . . . -0.3V to 18V

LI and HI Voltages . . . . . . . . . . . . . . . . . . . . . . . . .-3V to VDD +0.3V

Voltage on LO . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V

Voltage on HO . . . . . . . . . . . . . . . . . . . . . . VHS -0.3V to VHB +0.3V

Voltage on HS (Continuous) . . . . . . . . . . . . . . . . . . . . . -1V to 110V

Voltage on HB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +118V

Average Current in VDD to HB Diode. . . . . . . . . . . . . . . . . . . 100mA

ESD Classiﬁcation . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 (1kV)

Thermal Resistance (Typical, Note 1)

θJA (oC/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

HS Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V/ns

Maximum Power Dissipation at 25oC in Free Air . . . . . . . . . .780mW

Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC

Maximum Junction Temperature Range . . . . . . . . . -55oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC

(Lead Tips Only)

Recommended Operating Conditions

Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . +9V to +16.5V

Voltage on HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to 100V

Voltage on HS . . . . . . . . . . . . . . . (Repetitive Transient) -5V to 105V

Voltage on HB. . . VHS +8V to VHS +16.5V and VDD -1V to VDD +100V

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTES:

θJA is measured with the component mounted on an evaluation PC board in free air.

2. All Voltages Relative to Pin 4, VSS Unless Otherwise Specified.

Electrical Speciﬁcations

VDD = VHB = 12V, VSS = VHS = 0V, No Load on LO or HO, Unless Otherwise Speciﬁed

PARAMETER

SYMBOL

TEST CONDITIONS

TJ = 25

TJ = -40

TO 125oC

UNITS

MIN

TYP

MAX

MIN

MAX

SUPPLY CURRENTS

VDD Quiescent Current

IDD

LI = HI = 0V

0.1

0.15

0.2

VDD Operating Current

IDDO

f = 500kHz

1.5

2.5

Total HB Quiescent Current

IHB

LI = HI = 0V

0.1

0.15

0.2

Total HB Operating Current

IHBO

f = 500kHz

1.5

2.5

HB to VSS Current, Quiescent

IHBS

VHS = VHB = 116.5V

0.05

µA

HB to VSS Current, Operating

IHBSO

f = 500kHz

0.7

INPUT PINS

Low Level Input Voltage Threshold

VIL

5.4

High Level Input Voltage Threshold

VIH

5.8

Input Voltage Hysteresis

VIHYS

0.4

Input Pulldown Resistance

200

100

500

Ω

UNDER VOLTAGE PROTECTION

VDD Rising Threshold

VDDR

7.3

6.5

8.5

VDD Threshold Hysteresis

VDDH

0.5

HB Rising Threshold

VHBR

6.5

6.9

7.5

HB Threshold Hysteresis

VHBH

0.4

BOOT STRAP DIODE

Low-Current Forward Voltage

VDL

IVDD-HB = 100µA

0.45

0.55

0.7

High-Current Forward Voltage

VDH

IVDD-HB = 100mA

0.7

0.8

Dynamic Resistance

IVDD-HB = 100mA

0.8

1.5

Ω

LO GATE DRIVER

Low Level Output Voltage

VOLL

ILO = 100mA

0.25

0.3

0.4

High Level Output Voltage

VOHL

ILO = -100mA, VOHL = VDD-VLO

0.25

0.3

0.4

Peak Pullup Current

IOHL

VLO = 0V

Peak Pulldown Current

IOLL

VLO = 12V

HO GATE DRIVER

Low Level Output Voltage

VOLH

IHO = 100mA

0.25

0.3

0.4

High Level Output Voltage

VOHH

IHO = -100mA, VOHH = VHB-VHO

0.25

0.3

0.4

Peak Pullup Current

IOHH

VHO = 0V

HIP2106

HIP2106IP Datasheet(PDF) 3 Page - Intersil Corporation

HIP2106IP Datasheet(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8

Datasheet Download

Link URL