HSP9521 datasheet(3/4 Pages) INTERSIL

3 / 4 page

Absolute Maximum Ratings

Thermal Information

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V

Input or Output Voltage Applied . . . . . . . . . . GND -0.5 to VCC +0.5V

Operating Conditions

Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4.75V to 5.25V

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC

Thermal Resistance (Typical, Note 1)

θJA (oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . .

SOIC Package . . . . . . . . . . . . . . . . . . .

77.0

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC

Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

DC Electrical Speciﬁcations

VCC = 5.0V ±5%, TA = 0

oC to 70oC

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

MAX

UNITS

Logical One Input Voltage

VIH

VCC = 5.25V

2.0

Logical Zero Input Voltage

VIL

VCC = 4.75V

0.8

Output HIGH Voltage

VOH

IOH = -6.5mA, VCC - 4.75V

2.4

Output LOW Voltage

VOL

IOH = +20.0mA, VCC = 4.75V

0.5

Input Leakage Current

VIN = VCC or GND, VCC = 5.25V

-10

µA

Output Leakage Current

VOUT = VCC or GND, VCC = 5.25V

-10

µA

Standby Power Supply Current

ICCSB

VIN = VCC or GND, VCC = 5.25V Outputs Open

500

µA

Operating Power Supply Current

ICCOP

f = 5.0MHz, VIN = VCC or GND, VCC = 5.25V, Outputs

Open (Note 2)

-12

Input Capacitance

CIN

FREQ = 1MHZ, VCC = Open, All Measurements are

Referenced to Device Ground

-12

Output Capacitance

AC Electrical Speciﬁcations

VCC = 5.0V ±5%, TA = 0

oC to 70oC (Note 3)

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

MAX

UNITS

Clock to Data Out

tPD

-21

Mux Select to Data Out

tSELD

-20

Input Setup Time (DO-7/10-7)

Input Hold Time (DO-7/10-7)

Output Enable Time

tENA

-20

Output Disable Time

tDIS

(Note 4)

Clock Pulse Width

tPW

NOTES:

2. Power supply current is proportional to frequency. Typical rating for ICCOP is 2.4mA/MHz.

3. AC Testing is performed as follows: Input levels: 0V and 3.0V, timing reference levels = 1.5V, input rise and fall times driven at 1ns/V, output

load CL = 40pF.

4. Controlled by design or process parameters and not directly tested. Characterized upon initial design and after major design and/or process

changes.

HSP9520, HSP9521

HSP9521 Datasheet(PDF) 3 Page - Intersil Corporation

HSP9521 Datasheet(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4

Datasheet Download

Link URL