LT1210CS datasheet(3/16 Pages) LINER

3 / 16 page

LT1210

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

CMRR

Common Mode Rejection Ratio

VS = ±15V, VCM = ±12V

VS = ±5V, VCM = ±2V

Inverting Input Current

VS = ±15V, VCM = ±12V

0.1

µA/V

Common Mode Rejection

VS = ±5V, VCM = ±2V

0.1

µA/V

PSRR

Power Supply Rejection Ratio

VS = ±5V to ±15V

Noninverting Input Current

VS = ±5V to ±15V

500

nA/V

Power Supply Rejection

Inverting Input Current

VS = ±5V to ±15V

0.7

µA/V

Power Supply Rejection

Large-Signal Voltage Gain

TA = 25°C, VS = ±15V, VOUT = ±10V,

RL = 10Ω (Note 3)

VS = ±15V, VOUT = ±8.5V, RL = 10Ω (Note 3)

VS = ±5V, VOUT = ±2V, RL = 10Ω

ROL

Transresistance,

∆VOUT/∆IIN–

TA = 25°C, VS = ±15V, VOUT = ±10V,

RL = 10Ω (Note 3)

100

260

Ω

VS = ±15V, VOUT = ±8.5V, RL = 10Ω (Note 3)

200

Ω

VS = ±5V, VOUT = ±2V, RL = 10Ω

200

Ω

VOUT

Maximum Output Voltage Swing

TA = 25°C, VS = ±15V, RL = 10Ω (Note 3)

±10.0

±11.5

±8.5

TA = 25°C, VS = ±5V, RL = 10Ω±2.5

±3.0

±2.0

IOUT

Maximum Output Current (Note 3)

VS = ±15V, RL = 1Ω

1.1

2.0

Supply Current (Note 3)

TA = 25°C, VS = ±15V, VSD = 0V

Supply Current, RSD = 51k (Notes 3, 4)

TA = 25°C, VS = ±15V

Positive Supply Current, Shutdown

VS = ±15V, VSD = 15V

200

µA

Output Leakage Current, Shutdown

VS = ±15V, VSD = 15V

µA

Slew Rate (Note 5)

TA = 25°C, AV = 2, RL = 400Ω

400

900

µs

Slew Rate (Note 3)

TA = 25°C, AV = 2, RL = 10Ω

900

µs

Differential Gain (Notes 3, 6)

VS = ±15V, RF = 750Ω, RG = 750Ω, RL = 15Ω

0.3

Differential Phase (Notes 3, 6)

VS = ±15V, RF = 750Ω, RG = 750Ω, RL = 15Ω

0.1

DEG

Small-Signal Bandwidth

AV = 2, VS = ±15V, Peaking ≤ 1dB,

MHz

RF = RG = 680Ω, RL = 100Ω

AV = 2, VS = ±15V, Peaking ≤ 1dB,

MHz

RF = RG = 576Ω, RL = 10Ω

ELECTRICAL CHARACTERISTICS

VCM = 0V, ±5V ≤ VS ≤ ±15V, pulse tested, VSD = 0V, unless otherwise noted.

supply voltages greater than

±5V, use the TO-220 or DD package. See

“Thermal Considerations” in the Applications Information section for

details on calculating junction temperature. If the maximum dissipation of

the package is exceeded, the device will go into thermal shutdown.

Note 4: RSD is connected between the Shutdown pin and ground.

Note 5: Slew rate is measured at

±5V on a ±10V output signal while

operating on

±15V supplies with RF = 1.5k, RG = 1.5k and RL = 400Ω.

Note 6: NTSC composite video with an output level of 2V.

The q denotes specifications which apply for 0

°C ≤ TA ≤ 70°C.

Note 1: Applies to short circuits to ground only. A short circuit between

the output and either supply may permanently damage the part when

operated on supplies greater than

±10V.

Note 2: Commercial grade parts are designed to operate over the

temperature range of – 40

°C ≤ TA ≤ 85°C, but are neither tested nor

guaranteed beyond 0

°C ≤ TA ≤ 70°C. Industrial grade parts tested over

–40

°C ≤ TA ≤ 85°C are available on special request. Consult factory.

Note 3: SO package is recommended for

±5V supplies only, as the power

dissipation of the SO package limits performance on higher supplies. For

LT1210CS Datasheet(PDF) 3 Page - Linear Technology

LT1210CS Datasheet(HTML) 3 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Download

Link URL