LT1636CS8 datasheet(5/12 Pages) LINER

5 / 12 page

LT1636

SYMBOL

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Slew Rate

AV = – 1, RL = ∞, VO = ±10V Measured at ±5V

0.0375

0.075

µs

°C ≤ TA ≤ 70°C

0.033

µs

–40

°C ≤ TA ≤ 85°C

0.030

µs

VS = ±15V, VCM = 0V, VOUT = 0V, Pin 5 = open or VEE, Pins 1 and 8 open, TA = 25°C unless otherwise noted. (Note 3)

±15V ELECTRICAL CHARACTERISTICS

Note 4: VS = 5V limits are guaranteed by correlation to VS = 3V, and

VS = ±15V or VS = ±22V tests.

Note 5: VS = 3V limits are guaranteed by correlation to VS = 5V, and

VS = ±15V or VS = ±22V tests.

Note 6: Guaranteed by correlation to slew rate at VS = ±15V, and GBW at

VS = 3V and VS = ±15V tests.

Note 7: This specification implies a typical input offset voltage of 600

µV at

VCM = 44V and a maximum input offset voltage of 3mV at VCM = 44V.

Note 8: This parameter is not 100% tested.

TYPICAL PERFOR A CE CHARACTERISTICS

TOTAL SUPPLY VOLTAGE (V)

545

1636 G01

TA = 125°C

TA = 25°C

TA = –55°C

Supply Current vs Supply Voltage

COMMON MODE VOLTAGE (V)

4.0

–10

5.2 10 20 30 40

5000

1636 G03

4.4

4.8

1000

3000

VS = 5V, 0V

TA = –55°C

TA = 125°C

TA = 25°C

Input Bias Current

vs Common Mode Voltage

SOURCING LOAD CURRENT (mA)

0.0001 0.001

0.01

0.1

0.01

0.1

100

1636 G04

VS = 5V

VOD = 30mV

TA = 125°C

TA = 25°C

TA = –55°C

Output Saturation Voltage

vs Load Current (Output High)

INPUT OVERDRIVE (mV)

100

1636 G06

100

OUTPUT HIGH

OUTPUT LOW

VS = ±2.5V

NO LOAD

Output Saturation Voltage

vs Input Overdrive

Output Saturation Voltage

vs Load Current (Output Low)

SINKING LOAD CURRENT (mA)

0.0001 0.001

0.001

0.01

0.1

0.01

0.1

100

1636 G05

VS = 5V

VOD = 30mV

TA = 125°C

TA = –55°C

TA = 25°C

Minimum Supply Voltage

TOTAL SUPPLY VOLTAGE (V)

–300

–100

300

–200

200

100

1636 G02

TA = –55°C

TA = 125°C

TA = 25°C

The q denotes specifications that apply over the full specified temperature

range.

Note 1: Absolute Maximum Ratings are those values beyond which the life

of a device may be impaired.

Note 2: A heat sink may be required to keep the junction temperature

below absolute maximum.

Note 3: The LT1636C is guaranteed to meet specified performance from

°C to 70°C and is designed, characterized and expected to meet these

extended temperature limits, but is not tested at –40

°C and 85°C. The

LT1636I is guaranteed to meet the extended temperature limits.

LT1636CS8 Datasheet(PDF) 5 Page - Linear Technology

LT1636CS8 Datasheet(HTML) 5 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

Datasheet Download

Link URL