Electronic Components Datasheet Search
  English  ▼

X  

MAX847 Datasheet(PDF) 2 Page - Maxim Integrated Products

Part # MAX847
Description  1-Cell, Step-Up Two-Way Pager System IC
PDF  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MAXIM [Maxim Integrated Products]
Direct Link  https://www.maximintegrated.com/en.html
Logo MAXIM - Maxim Integrated Products

MAX847 Datasheet(HTML) 2 Page - Maxim Integrated Products

  MAX847 Datasheet HTML 1Page - Maxim Integrated Products MAX847 Datasheet HTML 2Page - Maxim Integrated Products MAX847 Datasheet HTML 3Page - Maxim Integrated Products MAX847 Datasheet HTML 4Page - Maxim Integrated Products MAX847 Datasheet HTML 5Page - Maxim Integrated Products MAX847 Datasheet HTML 6Page - Maxim Integrated Products MAX847 Datasheet HTML 7Page - Maxim Integrated Products MAX847 Datasheet HTML 8Page - Maxim Integrated Products MAX847 Datasheet HTML 9Page - Maxim Integrated Products Next Button
Zoom Inzoom in Zoom Outzoom out
 2 / 18 page
background image
1-Cell, Step-Up
Two-Way Pager System IC
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(OUT = 3.0V, BATT = 1.2V, NICD = 3.6V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
BATT, OUT, NICD, LBO, RSO to AGND...................-0.3V to +6V
REG1, OFS, REG2, REF, R2IN to AGND ...-0.3V to (OUT + 0.3V)
SCL, SDO, SDI, CS , SYNC, FILT, DR2IN,
CH0, LBI, RSIN, RUN to AGND ...................-0.3V to (REG1 + 0.3V)
REG3 .......................................................-0.3V to (REG2 + 0.3V)
DR1, DR2 to DRGND ...............................-0.3V to (BATT + 0.3V)
PGND, DRGND to AGND ......................................-0.3V to +0.3V
LX1 to PGND .............................................-0.3V to (OUT + 0.3V)
Continuous Power Dissipation (TA = +70°C)
28-Pin QSOP (derate 8mW/°C above +70°C) .............640mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10sec) .............................+300°C
TA = +25°C
Run or Coast Mode
Incremental supply current when on
REG2, REG3 and CH DAC off, VOUT = 2.8V
REG2, REG3 and CH DAC on
Coast mode
Incremental supply current when on
CONDITIONS
V
0.9
1.1
BATT Minimum Start-Up Voltage
(Note 3)
V
0.8
OUT x
0.8
BATT Typical Operating Range
(Note 2)
µA
30
CH DAC Supply Current (Note 4)
µA
13
25
Coast Mode Supply Current (Note 4)
µA
875
1350
Run Mode Supply Current (Note 4)
µA
0.5
2
BATT Supply Current (Note 5)
µA
20
REG3 Supply Current (Note 4)
UNITS
MIN
TYP
MAX
PARAMETER
IREF = 0 to 20µA, OUT = 1.8V to 4.9V
V
-1.5%
1.28
1.5%
Reference Voltage
IDR = 120mA
Ω
1.8
2.8
DR1, DR2 On-Resistance
VDR = 5V
nA
1
250
DR1, DR2 Leakage Current
TA = +25°C
TA = -40°C to +85°C
ISDO = 100µA
mV
200
SDO Output Low
ISDO = -100µA, from REG1
V
VREG1
- 0.2
SDO Output High
Includes CS, SDI, SCL, DR2IN, SYNC, and RUN
V
0.4
Logic Input Level Low
Includes CS, SDI, SCL, DR2IN, SYNC, and RUN
V
VREG1
- 0.4
Logic Input Level High
3.6
50% duty cycle
MHz
5
SCL Maximum Clock Rate
ns
100
SDI Setup Time, tDS
ns
50
SDI Hold Time, tDH
Logic Input = 0 to 3.3V; includes CS, SDI, SCL,
DR2IN, SYNC, and RUN
µA
-1
1
Logic Input Current
Charger and Backup Modes off, NICD = 3.6V
µA
1.2
3
NICD Input Current, Standby
(Note 6)
Incremental supply current when on
µA
Backup mode, NICD = 3.6V, OUT = 3V
50
REG2 Supply Current (Note 4)
µA
20
40
NICD Input Supply Current, Backup
(Note 7)
Charger and Backup Modes off,
BATT = 0V and OUT = 0V
µA
1.2
3
NICD Input Current, Power Fail
(Note 8)
GENERAL PERFORMANCE
SERIAL-INTERFACE TIMING SPECIFICATIONS (Note 9)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com