MAX9160EUI datasheet(2/13 Pages) MAXIM

2 / 13 page

LVDS or LVTTL/LVCMOS Input to

14 LVTTL/LVCMOS Output Clock Driver

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

DC ELECTRICAL CHARACTERISTICS

(VCC = 3.0V to 3.6V, ENA = ENB = high, RSET = 12k

Ω±1%, differential input voltage IVIDI = 0.05V to 1.2V, input common-mode volt-

age VCM = IVID/2 I to 2.4V - IVID/2 I, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = 3.3V, IVIDI = 0.2V,

VCM = 1.2V, TA = +25°C.) (Notes 2, 3)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

VCC to GND ..............................................................-0.3V to +4V

IN+, IN- to GND........................................................-0.3V to +4V

SE_IN, EN_, SEL, RSET, OUT_ to GND ........-0.3V to VCC + 0.3V

Output Short-Circuit Duration (OUT_) (Note 1) ..........Continuous

Continuous Power Dissipation (TA = +70°C)

28-Pin TSSOP (derate 12.8mW/°C above +70°C) .....1024mW

28-Pin TSSOP-EP (derate 23.8mW/°C above +70°C) ..1904mW

32-Pin QFN (derate 21.2mW/°C above +70°C) .........1704mW

Storage Temperature Range .............................-65°C to +150°C

Junction Temperature ......................................................+150°C

Operating Temperature Range ...........................-40

°C to +85°C

ESD Protection

Human Body Model (IN+, IN-) .......................................

±16kV

Human Body Model (SE_IN) ............................................

±8kV

Soldering Temperature (10s) ...........................................+300°C

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

SINGLE-ENDED INPUTS (SE_IN, ENA, ENB, SEL)

Input High Voltage

VIH

2.0

VCC

Input Low Voltage

VIL

GND

0.8

Input Clamp Voltage

VCL

ICL = -18mA

-1.5

-0.85

Input Current

IIN

VIN = high or low

-20

+20

µA

SE_IN Capacitance (Note 4)

CIN

SE_IN to GND

6.1

LVDS INPUT (IN+, IN-)

Differential Input High Threshold

VTH

Differential Input Low Threshold

VTL

-50

0.05V

≤ IVIDI ≤ 0.6V

-15

+15

Input Current

IIN+, IIN-

0.6V < IVIDI

≤ 1.2V

-20

+20

µA

0.05V

≤ IVIDI ≤ 0.6V, VCC = 0V or open

-15

+15

Power-Off Input Current

IIN+(off)

IIN-(off)

0.6V < IVIDI

≤ 1.2V, VCC = 0V or open

-20

+20

µA

Input Resistor 1

RIN1

VCC = 3.6V or 0V, Figure 1

100

Ω

Input Resistor 2

RIN2

VCC = 3.6V or 0 V, Figure 1

200

341

Ω

Input Capacitance (Note 4)

CIN

IN+ or IN- to GND

6.0

OUTPUTS (OUT_)

SEL = high, SE_IN = high, VOUT = 0V

Output Short-Circuit Current

(Note 1)

IOS

SEL = low, VID = 100mV, VOUT = 0V

-115

-30

Output Capacitance (Note 4)

OUT_ to GND

IOH = -100µA

VCC -

0.2

IOH = -4mA

2.4

Output High Voltage

VOH

IOH = -8mA

2.1

IOH = -100µA

VCC -

0.2

IOH = -4mA

2.4

Fail-Safe Output High Voltage

VOHFS

SEL = low, inputs

open, undriven short,

or undriven parallel

terminated

IOH = -8mA

2.1

Note 1: Short one output at a time. Do not exceed the absolute maximum junction temperature.

MAX9160EUI Datasheet(PDF) 2 Page - Maxim Integrated Products

MAX9160EUI Datasheet(HTML) 2 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

Datasheet Download

Link URL