MXD1013CSLASHD datasheet(2/6 Pages) MAXIM

2 / 6 page

3-in-1 Silicon Delay Line

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(VCC = +5.0V ±5%, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)(Note 1)

TIMING CHARACTERISTICS

(VCC = +5.0V ±5%, TA = +25°C, unless otherwise noted.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Note 1: Specifications to -40°C are guaranteed by design, not production tested.

Note 2: All voltages referenced to GND.

Note 3: Measured with outputs open.

Note 4: Guaranteed by design.

Note 5: Pulse width and/or period specifications may be exceeded, but accuracy is application sensitive (i.e., layout, decoupling, etc.).

Note 6: VCC = +5V at +25°C. Typical delays are accurate on both rising and falling edges within ±2ns for delays from 10ns to

60ns, within ±3% for delays from 70ns to 100ns, and within ±5% for delays from 150ns to 200ns.

Note 7: The

Part Number and Delay Times table provides typical delays at +25°C with VCC = +5V. The delays may shift with tem-

perature and supply variations. The combination of temperature (from +25°C to 0°C, or +25°C to +70°C) and supply varia-

tion (from 5V to 4.75V, or 5V to 5.25V) could produce an additional typical delay of ±1.5ns or ±3%, whichever is greater.

Note 8: All output delays tend to vary unidirectionally with temperature or supply voltage variations (i.e., if OUT1 slows down, all

other outputs also slow down).

VCC to GND ..............................................................-0.5V to +6V

All Other Pins..............................................-0.5V to (VCC + 0.5V)

Short-Circuit Output Current (1sec) ....................................50mA

Continuous Power Dissipation (TA = +70°C)

8-Pin Plastic DIP (derate 9.1mW/°C above +70°C) .......727mW

14-Pin Plastic DIP (derate 10.0mW/°C above +70°C) ...800mW

8-Pin SO (derate 5.9mW/°C above +70°C)....................471mW

16-Pin Narrow SO (derate 8.7mW/°C above +70°C) .....696mW

8-Pin µMAX (derate 4.1mW/°C above +70°C) ...............330mW

Operating Temperature Range ...........................-40°C to +85°C

Storage Temperature Range .............................-65°C to +160°C

Lead Temperature (soldering, 10sec) .............................+300°C

(Note 2)

TA = +25°C (Note 4)

≤ VIN ≤ VCC

VCC = 5.25V, period = minimum (Note 3)

VCC = 4.75V, VOH = 4.0V

VCC = 4.75V, VOL = 0.5V

CONDITIONS

0.8

VIL

Input Voltage Low

2.2

VIH

4.75

5.00

5.25

VCC

Supply Voltage

Input Voltage High

CIN

Input Capacitance

µA

-1

Input Leakage Current

ICC

Active Current

-1

IOH

Output Current High

IOL

Output Current Low

UNITS

MIN

TYP

MAX

SYMBOL

PARAMETER

(Notes 6, 7, 8)

(Note 5)

CONDITIONS

See Part Number and

Delay Times table

tPHL

Input-to-Output Delay

(trailing edge)

See Part Number and

Delay Times table

tPLH

100% of tPLH

tWI

Input Pulse Width

Input-to-Output Delay

(leading edge)

100

tPU

Power-Up Time

3(tWI)

Period

UNITS

MIN

TYP

MAX

SYMBOL

PARAMETER

MXD1013C/D Datasheet(PDF) 2 Page - Maxim Integrated Products

MXD1013C/D Datasheet(HTML) 2 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6

Datasheet Download

Link URL