ISL84684IR datasheet(3/13 Pages) INTERSIL

3 / 13 page

FN6088.5

July 31, 2007

Absolute Maximum Ratings

Thermal Information

V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 5.5V

Input Voltages

NO, NC, IN (Note 2). . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)

Output Voltages

COM (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)

Continuous Current NO, NC, or COM . . . . . . . . . . . . . . . . . ±300mA

Peak Current NO, NC, or COM

(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . ±500mA

ESD Rating

Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8kV

Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500V

Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4kV

Thermal Resistance (Typical)

θJA (°C/W)

10 Ld 3x3 TDFN Package (Note 3) . . . . . . . . . . . . .

110

10 Ld MSOP Package (Note 3) . . . . . . . . . . . . . . . .

190

Maximum Junction Temperature (Plastic Package). . . . . . . +150°C

Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

NOTES:

2. Signals on NC, NO, IN, or COM exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.

θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications - 3V Supply

Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.4V (Note 4),

Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

TEMP

(°C)

MIN

(Notes 5, 6)

TYP

MAX

(Notes 5, 6) UNITS

ANALOG SWITCH CHARACTERISTICS

Analog Signal Range, VANALOG

Full

V+

ON Resistance, rON

V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+,

(See Figure 5)

0.35

0.5

Full

0.7

rON Matching Between Channels,

ΔrON

V+ = 2.7V, ICOM = 100mA, VNO or VNC = Voltage at

max rON, (Note 8)

0.055

0.07

Full

0.08

rON Flatness, rFLAT(ON)

V+ = 2.7V, ICOM = 100mA, VNO or VNC = 0V to V+,

(Note 7)

0.03

0.15

Full

0.15

NO or NC OFF Leakage Current,

INO(OFF) or INC(OFF)

V+ = 3.3V, VCOM = 0.3V, 3V, VNO or VNC = 3V, 0.3V

-4

Full

-40

COM ON Leakage Current,

ICOM(ON)

+ = 3.3V, V

COM = 0.3V, 3V, or VNO or VNC = 0.3V,

3V, or Floating

-5

Full

-60

DYNAMIC CHARACTERISTICS

Turn-ON Time, tON

V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,

(See Figure 1)

Full

Turn-OFF Time, tOFF

V+ = 2.7V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,

(See Figure 1)

Full

Break-Before-Make Time Delay, tD V+ = 3.3V, VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF,

(See Figure 3)

Full

Charge Injection, Q

CL = 1.0nF, VG = 0V, RG = 0Ω, (See Figure 2)

OFF Isolation

RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,

(See Figure 4)

Crosstalk (Channel-to-Channel)

RL = 50Ω, CL = 5pF, f = 100kHz, VCOM = 1VRMS,

(See Figure 6)

-85

Total Harmonic Distortion

f = 20Hz to 20kHz, VCOM = 2VP-P, RL = 600Ω

0.005

NO or NC OFF Capacitance, COFF f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 7)

COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V, (See Figure 7)

181

ISL84684

ISL84684IR Datasheet(PDF) 3 Page - Intersil Corporation

ISL84684IR Datasheet(HTML) 3 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

Datasheet Download

Link URL