MB65S

65W Single Output

Medical Series

www.slpower.com

MB65S Aug -14

3

Overshoot

<2% overshoot at turn-on, <1% overshoot at turn-

off, under all conditions.

IPC 610

Class 2

HF Common Mode

Noise

0.8 Vrms maximum (input class I)

Safety Standards

IEC 60601-1, 3

ANSI/AAMI ES60601-1 (2008)

CAN/CSA – C22.2 No 60601-1 (2005)

DEMKO EN60601-1:2006

Designed to meet China Safety Doc. No. GB4943.1-

2011 at 5Km, Tropical Standard at 40°C, 93% RH at

120 hours.

Total Regulation

±1.0 % for all models.

Weight

140g, typical

Minimum Load

Not required.

Dimensions

W: 2.0” x L: 3.5” x H: 1.3”

W: 50.8mm x L: 88.9mm x H: 33.02mm

Additional Outputs

DC OK:

During normal operation, this signal is logic HIGH.

Signal will go LOW for output less than

80%

(typical) of nominal. Green LED will light on PCB

top side during normal operation.

PSU Temperature

Provides resistive value indicating internal

temperature of power supply. See Temp Sensor

Conversion Table below.

EMI/EMC Compliance

Conducted Emissions

EN55011/22: Class B, FCC Part 15. Class B: 6db margin typ, Class 1 PSU

configuration

EN55011/ 22: Class B, FCC Part 15. Class B: 2db margin typ, Class 2 PSU

configuration

Radiated Emissions

EN55011/22: Class B, FCC Part 15. Class B: 3db margin typ, Class 1 PSU

configuration.

EN55011/22: Class B, FCC Part 15. Class B: 3db margin typ, Class 2 PSU

configuration.

Harmonic Current Emissions

IEC61000-3-2: Class A

Voltage Fluctuations & Flicker

IEC 61000-3-3

Electro Static Discharge Immunity

IEC61000-4-2: Level 4, 8kV Contact Discharge, 15kV air discharge, Criteria A.

Also meets proposed IEC60601-1-2, 4

Radiated RF EM Fields Susceptibility

IEC61000-4-3: Level 3, 10V/m, Criteria A. 80MHz-1000 MHz and 3V/m 1.4Ghz

to 2.7 GHz. 80% AM at 1kHz. Also meets proposed IEC60601-1-2, 4

Table 4

Proximity Fields from RF wireless communications Equipment

[IEC60601-1-2: 4

Rated Power Frequency magnetic fields

IEC61000-4-8: Level 5, 30A/m, 50/60 Hz

Low Frequency magnetic fields

[TBD]

Electrical Fast Transients /Bursts

IEC61000-4-4: Level 3, 2KV, 100Khz rep rate, 40A (PS Output), Criteria A

IEC61000-4-4: Level 3, 1kV, 20A, (Other Outputs), Criteria B

Also meets proposed IEC60601-1-2, 4th edition standard, Table 5 & 6.

Surges Line to Line (DM) and Line to Ground (CM)

IEC61000-4-5: Level 3, +/-1kV DM, +/-2kV CM, Criteria A

Also meets proposed IEC60601-1-2, 4th edition standard, Table 5.

Conducted Disturbances induced by RF Fields

IEC61000-4-6: 3V/m & 10 V/m – 0.15 to 80Mhz and 10V/m in ISM and amateur

radio bands between 0.15 MHz and 80 MHz, 80% AM at 1 KHz

Also meets proposed IEC60601-1-2, 4th edition standard, Table 5 & 6 & 8.

Rated Power Frequency Magnetic Fields Test

IEC61000-4-8: Level 4 (30A/m), Criteria A

Also meets proposed IEC60601-1-2, 4

Voltage Dips

IEC61000-4-11: 100% dip for 10mS, at 0°, 45°, 90°, 135°, 180°, 225°, 270° and

315°, Criteria A; 60% dip for 100mS, Criteria B; 30% dip for 500mS (25/30 cycles)

1

∅, and 0° for 500mS, Criteria A. Also meets proposed IEC60601-1-2, 4

standard, Table 5.

Enclosure Port Immunity to RF wireless

communications equipment

IEC61000-4-3

Notes: Performance criteria are based on definitions contained in EN55024. Performance criteria are:

A – Normal performance during and after the test, B – Temporary degradation, self-recoverable, C – Temporary degradation, operator intervention required to recover the operation, D – Permanent

damage may occur