ME10

10W-12W Single Output External Power

Medical Series

www.slpower.com

ME10 Rev 2.5

31-JAN-16

2

Model

Output

Output

Ripple &

Line

Load

Output

Input

Number

Volts

Current

Power

Noise

¹

Regulation

Regulation

Connector

Configuration

ME10A0503C01

5.0V

2.0A

10W

75mV pk-pk

±1%

±5%

2.5 x 5.5 x 9.5mm

Straight Barrel Type,

center positive

Class II Wall-Plug,

Fixed North American

Blades³

ME10A0603C01

5.9V

1.6A

10W

75mV pk-pk

±1%

±5%

ME10A0703C01

7.5V

1.3A

10W

75mV pk-pk

±1%

±5%

ME10A1203C01

12.0V

1.0A

12W

120mV pk-pk

±1%

±5%

ME10A2403C01

24.0V

0.5A

12W

240mV pk-pk

±1%

±5%

Notes:

1. Measured at the output connector, with noise probe directly across output and load terminated with 0.1μF ceramic and 10μF low ESR capacitors. For 5V and

6V models, values listed are typical, 100mV pk-pk maximum with 0.1μF ceramic and 47μF low ESR capacitors used at measurement point.

2. Order blade kit KT-1027K for other blades (EU. UK, Australia)

3. For EU fixed blades, replace “C” in the model number with “M”, for UK blades, replace “C” with “G”, for Australia blades, replace “C” with “H”.

4. For Input Class I models: For AC GND connected to output common (-), insert a “B” in the part number where the “A” is located (ME10B0503F01).

5. All specifications are typical at nominal input, full load, at 25

°C ambient unless noted.

General Specifications

AC Input

100-240Vac, ±10%, 47-63Hz, 1

∅

Turn On Time

Less than 700mS @115Vac, full load

Input Current

115Vac: 0.45A, 230Vac: 0.28A

Hold-up Time

20mS min., at full Load, 100Vac input

Inrush Current

264Vac, cold start: will not exceed 40A

Overtemperature

Protection

Will shutdown upon an overtemperature

condition, auto-recovery.

Input Fuses

F1, F2: 3.15A, 250Vac fuses (line & neutral

lines) provided on all models

Overload Protection

130 to 180% of rating, Hiccup Mode

Earth Leakage

Current

Input-GND: <500μA@264Vac, 60Hz, NC

Output-GND: <4mA@264Vac, 60Hz, NC

Short Circuit

Protection

Hiccup Mode, auto recovery.

Efficiency

>87%, typical

Overvoltage

Protection

130 to 150% of output voltage, hiccup mode

Output Power

10 to 12W continuous – See models chart for

specific voltage model ratings.

Isolation

Input-Output:

2 MOPP

Input-Ground:

1 MOPP

Output-Ground: 1500Vac

No Load Input

Power

<0.1W per DoE Efficiency Level VI

Requirements

Safety Standards

EN/IEC/UL60601-1, 3rd edition and

EN/IEC/UL60601-1-11:2010 for Home

Healthcare

Ripple and Noise

See models chart on pg 1.

Operating

Temperature

-20°C to +50°C

all parameters are within published specifications).

Output Voltage

See models chart on pg 1.

Temperature

Derating

Derate output power above 40°C to TBD at

50°C

Transient

Response

500

µs response time for return to within 0.5%

of final value for any 50% load step over the

range of 5% to 100% of rated load,

∆i/∆t<

0.2A/

µs. Max. voltage deviation is +/-3.5%.

Storage Temperature

-40°C to +85°C

Regulation

See models chart on pg 1.

Altitude

Operating: to 5000m.

Non-operating: -500 to 40,000 ft.

Drop Test

1.4m from table top to wooden platform, 6

faces.

Relative Humidity

5% to 95%, non-condensing

Vibration

Operating: 0.003g/Hz, 1.5grms overall, 3

axes, 10 min/axis, 1-500Hz.

Non-Oper.: random waveform, 3 minutes per

axis, 3 axes and Sine waveform, Vib.

frequency/acceleration: 10-500Hz/1g, sweep

rate of 1 octave / minutes, Vibration time of 10

sweeps / axes, 3 axes

Shock

Operating: Half-sine, 20gpk, 10mS, 3 axes,

6 shocks total

Non-Operating: Half-sine waveform, impact

acceleration of 100G, Pulse duration of 6

mS, Number of shocks: 3 for each of the

three axis

E-Cap Life

>10 year life based on calculations at

115Vac/60Hz & 230Vac/50Hz, ambient 25°C

at 24 hrs per day, 365 days/year, 6 power up

cycles per day.

MTBF

>1,000,000 hours, full load, 110 & 220Vac

input, 25

°C amb., per Telcordia 332 Issue 6,

Stress Method.