MEC1322 datasheet(354/456 Pages) MICROCHIP

354 / 456 page

MEC1322

DS00001719D-page 354

 2014 - 2015 Microchip Technology Inc.

30.10.2.2

Asserting PREDRIVE_ENABLE

Disable Key Scan Interface (KSEN = '1')

Enable Predrive function (PREDRIVE_ENABLE = '1')

Program buffer type for all KSO pins to "push-pull”

Enable Keyscan Interface (KSEN ='0')

30.10.2.3

De-asserting PREDRIVE_ENABLE

Disable Key Scan Interface (KSEN = '1')

Program buffer type for all KSO pins to "open-drain”

Disable Predrive function (PREDRIVE_ENABLE = '0')

Enable Keyscan Interface (KSEN ='0')

30.10.3

INTERRUPT GENERATION

To support interrupt-based processing, an interrupt can optionally be generated on the high-to-low transition on any of

the KSI inputs. A running clock is not required to generate interrupts.

30.10.3.1

Runtime interrupt

KSC_INT is the block’s runtime active-high level interrupt. It is connected to the interrupt interface of the Interrupt Aggre-

gator, which then relays interrupts to the EC.

Associated with each KSI input is a status register bit and an interrupt enable register bit. A status bit is set when the

associated KSI input goes from high to low. If the interrupt enable bit for that input is set, an interrupt is generated. An

Interrupt is de-asserted when the status bit and/or interrupt enable bit is clear. A status bit cleared when written to a ‘1’.

Interrupts from individual KSIs are logically ORed together to drive the KSC_INT output port. Once asserted, an interrupt

is not asserted again until either all KSI[7:0] inputs have returned high or the has changed.

30.10.3.2

Wake-up Interrupt

KSC_INT_WAKE is the block’s wakeup interrupt. It is routed to the Interrupt Aggregator.

During sleep mode, i.e., when the bus clock is stopped, a high-to-low transition on any KSI whose interrupt enable bit

is set causes the KSC_INT_WAKE to be asserted. Also set is the associated status bit in the EC Clock Required 2 Status

The aforementioned transition on KSI also sets the corresponding status bit in the KSI STATUS Register. If enabled, a

runtime interrupt is also asserted on KSC_INT when the bus clock resumes running.

30.10.4

WAKE PROGRAMMING

Using the Keyboard Scan Interface to ‘wake’ the MEC1322 can be accomplished using either the Keyboard Scan Inter-

face wake interrupt, or using the wake capabilities of the GPIO Interface pins that are multiplexed with the Keyboard

Scan Interface pins. Enabling the Keyboard Scan Interface wake interrupt requires only a single interrupt enable access

and is recommended over using the GPIO Interface for this purpose.

30.11 EC-Only Registers

The registers listed in the EC-Only Register Summary table are for a single instance of the Keyboard Scan Interface.

The addresses of each register listed in this table are defined as a relative offset to the host “Base Address” defined in

the EC-Only Register Base Address Table.

The Base Address indicates where the first register can be accessed in a particular address space for a block instance.

TABLE 30-6:

EC-ONLY REGISTER BASE ADDRESS TABLE

Block Instance

Instance

Number

Host

Address Space

Base Address

Keyboard Scan

Interface

32-bit internal

address space

4000_9C00h

MEC1322 Datasheet(PDF) 354 Page - Microchip Technology

MEC1322 Datasheet(HTML) 354 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL