Electronic Components Datasheet Search
  English  ▼

X  

TLE6236G Datasheet(PDF) 10 Page - Infineon Technologies AG

Part # TLE6236G
Description  Smart Octal Low-Side Switch
PDF  15 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  INFINEON [Infineon Technologies AG]
Direct Link  http://www.infineon.com
Logo INFINEON - Infineon Technologies AG

TLE6236G Datasheet(HTML) 10 Page - Infineon Technologies AG

Back Button TLE6236G Datasheet HTML 6Page - Infineon Technologies AG TLE6236G Datasheet HTML 7Page - Infineon Technologies AG TLE6236G Datasheet HTML 8Page - Infineon Technologies AG TLE6236G Datasheet HTML 9Page - Infineon Technologies AG TLE6236G Datasheet HTML 10Page - Infineon Technologies AG TLE6236G Datasheet HTML 11Page - Infineon Technologies AG TLE6236G Datasheet HTML 12Page - Infineon Technologies AG TLE6236G Datasheet HTML 13Page - Infineon Technologies AG TLE6236G Datasheet HTML 14Page - Infineon Technologies AG Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 15 page
background image
Datasheet TLE 6236 G
V2.1
Page
26.Aug. 2002
10
SPI serial input (SI) bit overrides the parallel ON state control from IN1 to IN4
Vref is the threshold reference level for detecting an Open Load/Overload
The standard way of obtaining diagnostic information is as follows:
Clock in serial information into SI pin and wait approximately 200 µs to allow the outputs to
settle. Clock in the identical serial information once again - during this process the data com-
ing out at SO contains the bit combinations representing the diagnosis conditions as described
in figure 1.
Based on the needs of the application, a software routine should be programmed into the mi-
cro controller to set the corrective action of each fault condition.
Open Load Program Pin (OL/PRG)
To detect open load/short to ground each channel has an internal pull down source (300 µA
typ.) which pulls the drain voltage under the detection threshold in case of an open load or
short to ground condition.
If the TLE 6236 G is used to drive LEDs this pull down current could causes a slight glowing of
the LED. To avoid this, the device is provided with a program pin, which enables or disables
this open load detection. The OL/PRG pin is internally pulled up, i.e. the open load detection is
enabled if the OL/PRG pin is not connected. To disable the open load detection this pin must
be pulled to GND, e.g with a micro controller port.
In this way the open load detection can be enabled (e.g during start up of the system or in a
diagnosis routine) and disabled (e.g. during normal operation to avoid LED glowing) by the µC.
If the open load detection is disabled, the leakage current is reduced to a maximum of 1µA.
VBat
VDS
≈ 3.5V
OL
300µ
OL
OL
Vref
OL/PRG



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com