EM78P447SAM datasheet(30/55 Pages) EMC

30 / 55 page

EM78P447S

OTP ROM

4.12 Instruction Set

Each instruction in the instruction set is a 13-bit word divided into an OP code and one or more operands. Normally, all

instructions are executed within one single instruction cycle (one instruction consists of 2 oscillator periods), unless the

program counter is changed by instruction "MOV R2,A", "ADD R2,A", or by instructions of arithmetic or logic operation on

R2 (e.g. "SUB R2,A", "BS(C) R2,6", "CLR R2",

⋅⋅⋅⋅). In this case, the execution takes two instruction cycles.

If for some reasons, the specification of the instruction cycle is not suitable for certain applications, try modifying the

instruction as follows:

(A) Change one instruction cycle to consist of 4 oscillator periods.

(B) Executed within two instruction cycles, "JMP", "CALL", "RET", "RETL", "RETI", or the conditional

skip ("JBS", "JBC", "JZ", "JZA", "DJZ", "DJZA") instructions which were tested to be true. Also

execute within two instruction cycles, the instructions that are written to the program counter.

Case (A) is selected by the CODE Option bit, called CLK. One instruction cycle consists of two oscillator clocks if CLK is

low, and four oscillator clocks if CLK is high.

Note that once the 4 oscillator periods within one instruction cycle is selected as in Case (A), the internal clock source to

TCC should be CLK=Fosc/4, not Fosc/ 2 as indicated in Fig. 5.

In addition, the instruction set has the following features:

(1) Every bit of any register can be set, cleared, or tested directly.

(2) The I/O register can be regarded as general register. That is, the same instruction can operate on

I/O register.

The symbol "R" represents a register designator that specifies which one of the registers (including operational registers

and general purpose registers) is to be utilized by the instruction. "b" represents a bit field designator that selects the value

for the bit which is located in the register "R", and affects operation. "k" represents an 8 or 10-bit constant or literal value.

INSTRUCTION BINARY

HEX

MNEMONIC

OPERATION

STATUS AFFECTED

0 0000 0000 0000

0000

NOP

No Operation

None

0 0000 0000 0001

0001

DAA

Decimal Adjust A

0 0000 0000 0010

0002

CONTW

→ CONT

None

0 0000 0000 0011

0003

SLEP

→ WDT, Stop oscillator

T,P

0 0000 0000 0100

0004

WDTC

→ WDT

T,P

0 0000 0000 rrrr

000r

IOW R

→ IOCR

None <Note1>

0 0000 0001 0000

0010

ENI

Enable Interrupt

None

0 0000 0001 0001

0011

DISI

Disable Interrupt

None

0 0000 0001 0010

0012

RET

[Top of Stack]

→ PC

None

0 0000 0001 0011

0013

RETI

[Top of Stack]

→ PC,

Enable Interrupt

None

0 0000 0001 0100

0014

CONTR

CONT

→ A

None

This specification is subject to change without prior notice.

06.25.2003 (V1.1)

EM78P447SAM Datasheet(PDF) 30 Page - ELAN Microelectronics Corp

EM78P447SAM Datasheet(HTML) 30 Page - ELAN Microelectronics Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

Datasheet Download

Link URL