Electronic Components Datasheet Search
  English  ▼

X  

LT1970CFE Datasheet(PDF) 7 Page - Linear Technology

Part # LT1970CFE
Description  500mA Power Op Amp with Adjustable Precision Current Limit
PDF  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LT1970CFE Datasheet(HTML) 7 Page - Linear Technology

Back Button LT1970CFE Datasheet HTML 3Page - Linear Technology LT1970CFE Datasheet HTML 4Page - Linear Technology LT1970CFE Datasheet HTML 5Page - Linear Technology LT1970CFE Datasheet HTML 6Page - Linear Technology LT1970CFE Datasheet HTML 7Page - Linear Technology LT1970CFE Datasheet HTML 8Page - Linear Technology LT1970CFE Datasheet HTML 9Page - Linear Technology LT1970CFE Datasheet HTML 10Page - Linear Technology LT1970CFE Datasheet HTML 11Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 12 page
background image
7
LT1970
1970f
PI FU CTIO S
VEE (Pins 1, 10, 11, 20, Package Base): Minus Supply
Voltage. VEE connects to the substrate of the integrated
circuit die, and therefore must always be the most negative
voltage applied to the part. Decouple VEE to ground with a
low ESR capacitor. VEE may be a negative voltage or it may
equal ground potential. Any or all of the VEE pins may be
used. Unused VEE pins must remain open.
V– (Pin 2): Output Stage Negative Supply. V– may equal
VEE or may be smaller in magnitude. Only output stage
current flows out of V–, all other current flows out of VEE.
V– may be used to drive the base/gate of an external power
device to boost the amplifier’s output current to levels
above the rated 500mA of the on-chip output devices.
Unless used to drive boost transistors, V– should be
decoupled to ground with a low ESR capacitor.
OUT (Pin 3): Amplifier Output. The OUT pin provides the
force function as part of a Kelvin sensed load connection.
OUT is normally connected directly to an external load
current sense resistor and the SENSE+ pin. Amplifier
feedback is directly connected to the load and the other
end of the current sense resistor. The load connection is
also wired directly to the SENSE– pin to monitor the load
current.
The OUT pin is current limited to
±800mA typical. This
current limit protects the output transistor in the event
that connections to the external sense resistor are opened
or shorted which disables the precision current limit
function.
SENSE+ (Pin 4): Positive Current Sense Pin. This lead is
normally connected to the driven end of the external sense
resistor. Positive current limit operation is activated when
the voltage VSENSE (VSENSE+ – VSENSE–) equals 1/10 of
the programming control voltage at VCSRC (Pin 13). Nega-
tive current limit operation is activated when the voltage
VSENSE equals –1/10 of the programming control voltage
at VCSNK (Pin 12).
FILTER (Pin 5): Current Sense Filter Pin. This pin is
normally not used and should be left open in most appli-
cations. When very large capacitive loads are driven, a
filter capacitor connected between FILTER and SENSE+
will reduce overshoot as the amplifier enters current
limiting mode. The filter time constant is set by an internal
1k resistor and the external filter capacitor. Capacitor
values of 1nF to 100nF are most effective at reducing
overshoot.
SENSE– (Pin 6): Negative Current Sense Pin. This pin is
normally connected to the load end of the external sense
resistor. Positive current limit operation is activated when
the voltage VSENSE (VSENSE+ – VSENSE–) equals 1/10 of
the programming control voltage at VCSRC (Pin 13).
Negative current limit operation is activated when the
voltage VSENSE equals –1/10 of the programming control
voltage at VCSNK (Pin 12).
VCC (Pin 7): Positive Supply Voltage. All circuitry except
the output transistors draw power from VCC. Total supply
voltage from VCC to VEE must be between 3.5V and 36V.
VCC must always be greater than or equal to V+. VCCshould
always be decoupled to ground with a low ESR capacitor.
– IN (Pin 8): Inverting Input of Amplifier. – IN may be any
voltage from VEE – 0.3V to VEE + 36V. – IN and + IN remain
high impedance at all times to prevent current flow into the
inputs when current limit mode is active. Care must be
taken to insure that – IN or + IN can never go to a voltage
below VEE – 0.3V even during transient conditions or
damage to the circuit may result. A Schottky diode from
VEE to – IN can provide clamping if other elements in the
circuit can allow – IN to go below VEE.
+ IN (Pin 9): Noninverting Input of Amplifier. + IN may be
any voltage from VEE – 0.3V to VEE + 36V. – IN and +IN
remain high impedance at all times to prevent current flow
into the inputs when current limit mode is active. Care
must be taken to insure that – IN or + IN can never go to a
voltage below VEE – 0.3V even during transient conditions
or damage to the circuit may result. A Schottky diode from
VEE to +IN can provide clamping if other elements in the
circuit can allow + IN to go below VEE.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com