| Electronic Components Datasheet Search |
|
HV9910C Datasheet(PDF) 8 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
HV9910C Datasheet(HTML) 8 Page - Microchip Technology |
|
8 / 18 page ![]() HV9910C DS20005323A-page 8 2014 Microchip Technology Inc. the output of the OR GATE is fed into the reset pin of the flip-flop. Thus, the comparator which has the lowest voltage at the inverting terminal determines when the GATE output is turned off. The outputs of the comparators also include a 150- 280ns blanking time which prevents spurious turn-offs of the external FET due to the turn-on spike normally present in peak-current mode control. In rare cases, this internal blanking might not be enough to filter out the turn-on spike. In these instances, an external RC fil- ter needs to be added between the external sense resistor (RCS) and the CS pin. Please note that the comparators are fast (with a typi- cal 80ns response time). A proper layout minimizing external inductances will prevent false triggering of these comparators. 3.3 Oscillator The oscillator in HV9910C is controlled by a single resistor connected at the RT pin. The equation govern- ing the oscillator time period Tosc is given by: If the resistor is connected between RT and GND, HV9910C operates in a constant frequency mode and the above equation determines the time period. If the resistor is connected between RT and GATE, HV9910C operates in a constant off-time mode and the above equation determines the off-time. 3.4 Gate Output The gate output of the HV9910C is used to drive an external FET. It is recommended that the GATE charge of the external FET be less than 25nC for switching fre- quencies ≤ 100kHz and less than 15nC for switching frequencies > 100kHz. 3.5 Linear Dimming The Linear Dimming pin is used to control the LED cur- rent. There are two cases when it may be necessary to use the Linear Dimming pin. 1. In some cases, when using the internal 250mV, it may not be possible to find the exact RCS value required to obtain the LED current. In these cases, an external voltage divider from the VDD pin can be connected to the LD pin to obtain a voltage (less than 250mV) corresponding to the desired voltage across RCS. 2. Linear dimming may be desired to adjust the current level to reduce the intensity of the LEDs. In these cases, an external 0-250mV voltage can be connected to the LD pin to adjust the LED current during operation. To use the internal 250mV, the LD pin can be con- nected to VDD. 3.6 PWM Dimming PWM Dimming can be achieved by driving the PWMD pin with a low frequency square wave signal. When the PWM signal is zero, the GATE driver is turned off; when the PWMD signal if high, the GATE driver is enabled. The PWMD signal does not turn off the other parts of the IC, therefore, the response of HV9910C to the PWMD signal is almost instantaneous. The rate of rise and fall of the LED current is thus determined solely by the rise and fall times of the inductor current. To disable PWM Dimming and enable the HV9910C permanently, connect the PWMD pin to VDD. 3.7 Over-Temperature Protection The auto-recoverable thermal shutdown at 140°C (typ.) junction temperature with 20°C hysteresis is featured to avoid thermal runaway. When the junction tempera- ture reaches TSD = 140°C (typ.), HV9910C enters a low power consumption shut-down mode with IIN <350µA. TOSC s ROSC k 25 --------------------------- = Note: Although the LD pin can be pulled to GND, the output current will not go to zero. This is due to the presence of a minimum on- time, which is equal to the sum of the blanking time and the delay to output time, or about 450ns. This minimum on-time causes the FET to be on for a minimum of 450ns, and thus the LED current when LD = GND is not zero. This current is also dependent on the input voltage, induc- tance value, forward voltage of the LEDs, and circuit parasitics. To get zero LED cur- rent, the PWMD pin has to be used. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |