AD1833ACST datasheet(15/20 Pages) AD

15 / 20 page

REV. 0

AD1833A

–15–

TDM Mode Timing—Interfacing to a SHARC

In TDM mode, the AD1833A can be the master or slave, depend-

ing on Bit 0 in Control Register 3. In master mode, it generates a

frame sync signal (FSTDM) on its L/RCLK pin and a bit clock

(BCLKTDM) on its BCLK pin, whereas in slave mode it expects

these signals to be provided. These signals are used to control

the data transmission from the SHARC. The bit clock must run

at a frequency of IMCLK/2 and the interpolation mode must be

set to 8 , which limits TDM mode to frequencies of 48 kHz or

less. In this mode, all data is written on the rising edge of the bit

clock and read on the falling edge of the bit clock. The frame

starts with a frame sync at the rising edge of the bit clock. The

SHARC then starts outputting data on the next rising edge of

the bit clock. Each channel is given a 32-bit clock slot, and the

data is left-justified and uses 16, 20, or 24 of the 32 bits. An

enlarged diagram detailing this is provided (see Figure 9). The

data is sent from the SHARC to the AD1833A on the SDIN1

pin and provided in the following order: MSB first—Internal

DACL0, Internal DACL1, Internal DACL2, AUX DACL0,

Internal DACR0, Internal DACR1, Internal DACR2, and AUX

DACR0. The data is written on the rising edge of the bit clock

and read by the AD1833A on the falling edge of the bit clock.

The left and right data destined for the auxiliary DAC is sent in

standard I

2S format in the next frame using the SDIN2, SDIN3,

and SOUT pins as the L/RCLK, BCLK, and SDATA pins,

respectively, for communicating with the auxiliary DAC.

DSP Mode Timing

DSP mode timing uses the rising edge of the frame sync signal

on the L/RCLK pin to denote the start of the transmission of a

data-word. Note that for both left and right channels, a rising

edge is used; therefore in this mode, there is no way to determine

which data is intended for the left channel and which is intended

for the right. The DSP writes data on the rising edge of BCLK

and the AD1833A reads it on the falling edge. The DSP raises

the frame sync signal on the rising edge of BCLK and then proceeds

to transmit data, MSB first, on the next rising edge of BCLK.

The data length can be 16, 20, or 24 bits. The frame sync signal

can be brought low any time at or after the MSB is transmitted,

but must be brought low at least one BCLK period before the

start of the next channel transmission.

INTERNAL

DAC L0

INTERNAL

DAC L1

INTERNAL

DAC L2

AUXILIARY

DAC L0

INTERNAL

DAC R0

INTERNAL

DAC R1

INTERNAL

DAC R2

AUXILIARY

DAC R0

FSTDM

BCLKTDM

MSB

24-BIT DATA

20-BIT DATA

16-BIT DATA

BCLKTDM

MSB

–1

MSB

–2

MSB

–3

MSB

–4

LSB

MSB

–1

MSB

–2

MSB

–3

MSB

–4

LSB

MSB

–1

MSB

–2

MSB

–3

MSB

–4

LSB

Figure 9. TDM Mode Timing

L/RCLK

BCLK

SDATA

MSB

–1

MSB

–2

MSB

–4

MSB

–5

MSB

–6

MSB

–1

MSB

–2

MSB

–3

MSB

–4

MSB

–5

MSB

–6

MSB

32 BCLKs

MSB

–3

Figure 10. DSP Mode Timing

AD1833ACST Datasheet(PDF) 15 Page - Analog Devices

AD1833ACST Datasheet(HTML) 15 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Download

Link URL