| Electronic Components Datasheet Search |
|
MPC9658 Datasheet(PDF) 7 Page - Motorola, Inc |
|
|
|||||||||||||||||||||||||||||
MPC9658 Datasheet(HTML) 7 Page - Motorola, Inc |
|
7 / 12 page ![]() MPC9658 TIMING SOLUTIONS 7 MOTOROLA Using the MPC9658 in zero–delay applications Nested clock trees are typical applications for the MPC9658. Designs using the MPC9658 as LVCMOS PLL fanout buffer with zero insertion delay will show significantly lower clock skew than clock distributions developed from CMOS fanout buffers. The external feedback option of the MPC9658 clock driver allows for its use as a zero delay buffer. The PLL aligns the feedback clock output edge with the clock input reference edge resulting a near zero delay through the device (the propagation delay through the device is virtually eliminated). The maximum insertion delay of the device in zero-delay applications is measured between the reference clock input and any output. This effective delay consists of the static phase offset, I/O jitter (phase or long-term jitter), feedback path delay and the output-to-output skew error relative to the feedback output. Calculation of part-to-part skew The MPC9658 zero delay buffer supports applications where critical clock signal timing can be maintained across several devices. If the reference clock inputs of two or more MPC9658 are connected together, the maximum overall timing uncertainty from the common PCLK input to any output is: tSK(PP) = t( ∅) + tSK(O) + tPD, LINE(FB) + tJIT(∅) CF This maximum timing uncertainty consist of 4 components: static phase offset, output skew, feedback board trace delay and I/O (phase) jitter: Figure 4. MPC9658 max. device-to-device skew tPD,LINE(FB) tJIT( ∅) +tSK(O) –t( ∅) +t( ∅) tJIT( ∅) +tSK(O) tSK(PP) Max. skew PCLKCommon QFBDevice 1 Any QDevice 1 QFBDevice2 Any QDevice 2 Due to the statistical nature of I/O jitter a RMS value (1 s) is specified. I/O jitter numbers for other confidence factors (CF) can be derived from Table 8. Table 8. Confidence Facter CF CF Probability of clock edge within the distribution ± 1s 0.68268948 ± 2s 0.95449988 ± 3s 0.99730007 ± 4s 0.99993663 ± 5s 0.99999943 ± 6s 0.99999999 The feedback trace delay is determined by the board layout and can be used to fine-tune the effective delay through each device. In the following example calculation a I/O jitter confidence factor of 99.7% ( ± 3s) is assumed, resulting in a worst case timing uncertainty from input to any output of -214 ps to 224 ps relative to PCLK (fREF = 100 MHz, FB= ÷4, tjit(∅)=8 ps RMS at fVCO = 400 MHz): tSK(PP) = [–70ps...80ps] + [–120ps...120ps] + [(8ps @ –3)...(8ps @ 3)] + tPD, LINE(FB) tSK(PP) = [–214ps...224ps] + tPD, LINE(FB) Due to the frequency dependence of the I/O jitter, figure 5. can be used for a more precise timing performance analysis. Figure 5. Max. I/O Jitter versus frequency VCO frequency [MHz] 200 250 300 350 400 450 500 20 15 10 5 0 FB= ÷2 FB= ÷4 I/O Phase Jitter versus Frequency Parameter: PLL Feedback Divider FB Driving Transmission Lines The MPC9658 clock driver was designed to drive high speed signals in a terminated transmission line environment. To provide the optimum flexibility to the user the output drivers were designed to exhibit the lowest impedance possible. With an output impedance of less than 20 Ω the drivers can drive either parallel or series terminated transmission lines. For more information on transmission lines the reader is referred to Motorola application note AN1091. In most high performance clock networks point-to-point distribution of signals is the method of choice. In a point-to-point scheme either series terminated or parallel terminated transmission lines can be used. The parallel technique terminates the signal at the end of the line with a 50 Ω resistance to VCC÷2. This technique draws a fairly high level of DC current and thus only a single terminated line can be driven by each output of the MPC9658 clock driver. For the series terminated case however there is no DC current draw, thus the outputs can drive multiple series terminated lines. Figure 6. “Single Freescale Semiconductor, Inc. For More Information On This Product, Go to: www.freescale.com |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |