Typical Performance Characteristics

www.vishay.com

Vishay Sprague

Revision: 26-Jun-17

3

Document Number: 40215

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ENVIRONMENTAL PERFORMANCE CHARACTERISTICS

ITEM

CONDITION

POST TEST PERFORMANCE

High temperature

exposure (storage)

MIL-STD-202, method 108

1000 h, at maximum rated temperature,

unpowered

Capacitance change

Dissipation factor

Leakage current

ESR

Within ± 20 % of initial value

Initial specified limit

Initial specified limit

Initial specified limit

Operational life test

at +125 °C

AEC-Q200

1000 h application 2/3 of rated voltage

Capacitance change

Dissipation factor

Leakage current

ESR

Within ± 20 % of initial value

Initial specified limit

Shall not exceed 10 times the initial limit

Initial specified limit

Operational life test

at +150 °C (for TH3)

and at +175 °C

(for TH4)

AEC-Q200

1000 h application 1/2 of rated voltage

Capacitance change

Dissipation factor

Leakage current

ESR

Within ± 20 % of initial value

Shall not exceed 3 times the initial limit

Shall not exceed 10 times the initial limit

Shall not exceed 3 times the initial limit

Surge voltage

MIL-PRF-55365:

1000 successive test cycles at 85 °C of surge

voltage (as specified in the table above), in

series with a 33

Ω resistor at the rate of

30 s ON, 30 s OFF

Capacitance change

Dissipation factor

Leakage current

ESR

Within ± 30 % of initial value

Shall not exceed 1.5 times the initial limit

Shall not exceed 2 times the initial limit

Shall not exceed 1.5 times the initial limit

Biased humidity test

AEC-Q200

At 85 °C / 85 % RH, 1000 h,

with rated voltage applied

Capacitance change

Dissipation factor

Leakage current

ESR

Within ± 20 % of initial value

Shall not exceed 3 times the initial limit

Shall not exceed 10 times the initial limit

Shall not exceed 3 times the initial limit

Temperature cycling

AEC-Q200 / JESD22, method JA-104

-55 °C / +125 °C, for 1000 cycles

Capacitance change

Dissipation factor

Leakage current

ESR

Within ± 20 % of initial value

Initial specified limit

Initial specified limit

Initial specified limit

MECHANICAL PERFORMANCE CHARACTERISTICS

ITEM

CONDITION

POST TEST PERFORMANCE

Vibration

MIL-STD-202, method 204: 10 Hz to 2000 Hz, 5 g

peak for 20 min, 12 cycles each of 3 orientations

(total 36 cycles), at rated voltage

Capacitance change

Dissipation factor

Leakage current

Within ± 20 % of initial value

Initial specified limit

Initial specified limit

There shall be no mechanical or visual damage to

capacitors post-conditioning.

Mechanical shock

MIL-STD-202, method 213, condition F, 1500 g peak,

0.5 ms, half-sine

Capacitance change

Dissipation factor

Leakage current

Within ± 20 % of initial value

Initial specified limit

Initial specified limit

There shall be no mechanical or visual damage to

capacitors post-conditioning.

Resistance

to solder heat

MIL-STD-202, method 210, condition D

Solder dip 260 °C ± 5 °C, 10 s

Capacitance change

Dissipation factor

Leakage current

Within ± 20 % of initial value

Initial specified limit

Initial specified limit

Resistance to

solvents

MIL-STD-202, method 215

Capacitance change

Dissipation factor

Leakage current

Within ± 20 % of initial value

Initial specified limit

Initial specified limit

There shall be no mechanical or visual damage to

capacitors post-conditioning.

Body marking shall remain legible.

Solderability

AEC-Q200 / J-STD-002

Electrical test not required

Terminal strength /

Shear force test

AEC-Q200-006

Apply a pressure load of 17.7 N (1.8 kg) for 60 s

horizontally to the center of capacitor side body

Exception: for case size 0603 pressure load is 5N

Part should not be sheared off the pads and no body

cracking post-conditioning. Electrical test not required.

Flammability

Encapsulation materials meet UL 94 V-0 with an

oxygen index of 32 %

n/a