CS6422-CS datasheet(29/48 Pages) CIRRUS

29 / 48 page

CS6422

3.9

Reset

A hardware reset, initiated by bringing RST low for

at least tRSTL and then high again, must be applied

after initial power-on.

When RST is held low, the various internal blocks

of the CS6422 are powered down. When RST is

brought high, the oscillator is enabled and approx-

imately 4 ms later, all digital clocks begin operat-

ing. The ADCs and DACs are calibrated and all

internal digital initializations occur.

The CS6422 supports two reset modes, cold reset

and warm reset. The reset mode is selected by

completing a write of a specified value to the MCR

within TwRST of the rising edge of RST. If no

writes to the MCR occur within TcRST, then a cold

reset is initiated by default at the end of the TcRST

time period.

The value written to the MCR determines the be-

havior of the CS6422:

1) a value of ‘0x0000’ will initiate a cold reset

when the reset timer expires. This is the default

behavior of the device.

2) a value of ‘0x0006’ will initiate a warm reset

when the reset timer expires.

3) a value of ‘0x8000’ will initiate a cold reset im-

mediately, bypassing the reset timer.

4) a value of ‘0x8006’ will initiate a warm reset

immediately, bypassing the reset timer.

Values (#2) through (#4) above are interpreted as

legitimate register writes (to register 0 for (#3) and

to register 3 for (#2) and (#4)) of the CS6422.

Therefore, it is important to follow the first register

write with another write containing the proper set-

tings for register 0 or register 3.

3.9.1

Cold Reset

Cold reset initializes all the components of the

CS6422. The ADCs and DACs are reset, the echo

canceller memories and registers are cleared, and

the default settings of the MCR are restored.

3.9.2

Warm Reset

Warm reset is like cold reset except that the echo

canceller coefficients and certain key variables are

not cleared, but instead keep their pre-reset value.

This gives the CS6422 a headstart in adapting to its

environment if the echo environment is relatively

stable, assuming a cold reset occurred at least once

since power up.

3.9.3

Reset Timer

Another special reset option is to exit the TwRST re-

set timer before the TwRST has elapsed. This timer

halts device operation until the analog bias voltages

have had time to settle.

The early-exit option

should be used only in applications in which the

TwRST start-up delay is unacceptable.

3.10

Clocking

The clock for the converters and DSP is provided

via the clocking pins, CLKI (pin 14) and CLKO

(pin 13). A 20.480 MHz parallel resonant crystal

placed between these two pins and loaded with

22 pF capacitors will allow the on-chip oscillator to

provide this system clock. Alternatively, the CLKI

pin may be driven by a CMOS level clock signal.

The clock may vary from 20.480 MHz by up to

10%, however, this will change the sampling rate

of the converters and echo canceller, which will af-

fect the bandwidth of the analog signals and the du-

ration of echo that the echo canceller can

accommodate. CLKO is not connected when CLKI

is driven by the CMOS signal.

CS6422

DS295F1

CS6422-CS Datasheet(PDF) 29 Page - Cirrus Logic

CS6422-CS Datasheet(HTML) 29 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Datasheet Download

Link URL